Qilux Lighting

Light Quality Explained: CRI, CCT, TM-30 and SDCM

Light Quality Explained: CRI, CCT, TM-30 and SDCM

Four numbers decide whether a lighting scheme reads as designed or as a compromise: CRI, TM-30 Rf and Rg, CCT, and SDCM. They answer four different questions, and a specification that names only one of them leaves the supplier free to fail the other three. This guide sets out what each number measures, where it misleads, and which values hold up on hotel, restaurant and retail projects. Most CRI lighting arguments on site are really arguments about a metric being asked to do a job it was never built for.

1. The four numbers that define light quality

A light source emits a spectrum. The eye turns that spectrum into three impressions: how accurately colours appear, how warm or cool the white looks, and whether two fixtures of the same type appear to match. The four numbers map onto those impressions, and none of them is a substitute for another.

Overview of CRI, CCT, TM-30 and SDCM and the different light quality questions each metric addresses
MetricQuestion it answersCommon project valueWhat it misses
CRI (Ra)Average colour fidelity on eight pastel samplesRa ≥ 90 in guest areas, ≥ 80 back of houseSaturated reds and blues, R9 in particular
TM-30 (Rf, Rg)Fidelity across 99 samples plus gamut directionRf ≥ 90, Rg 97–103Published by fewer suppliers; no legal minimum
CCTWhere white sits on the warm-to-cool axis2700 K guestrooms, 3000 K public areasNothing about fidelity or consistency
SDCMHow far a fixture sits from its nominal CCT point≤ 3-step, ideally ≤ 2-stepOptics, dimming behaviour, ageing

Each row fails in its own way. A fixture can hit Ra 92 and still turn a rare steak grey, because the eight samples behind Ra contain no saturated red. It can sit exactly on 3000 K and still be four steps away from the fixture installed beside it. It can match on both counts and still produce a visible ring on a wall, because the reflector is wrong.

Two further variables belong in the conversation even though they do not appear in the table. The first is spectrum continuity around 480 nm, where phosphor-converted LEDs often dip; the dip shows up as dull teal and muddy olive. The second is dimming behaviour, since a driver that shifts colour temperature or starts to flicker at 5% output will undo a good spectrum.

Get this wrong and the cost lands late. Re-lamping 200 guestroom downlights after handover means new fittings, labour, access equipment and rooms off inventory while the work is done. Replacing 40 m of corridor coving because the second batch reads greener is worse, because the ceiling has to be opened. The numbers cost a few lines in a specification document; the failure costs a variation order.

The practical consequence is simple. Ask for all four numbers on one page per SKU, from the same test report, and treat a supplier who can only supply one of them as a supplier who has not measured the other three.

2. CRI: what Ra measures and what it misses

CRI was published by CIE in 1965 and revised in 1995 as CIE 13.3. It compares a test source against a reference source of the same colour temperature — a blackbody radiator below 5000 K, daylight above it — using eight Munsell-based colour samples, R1 to R8. Those samples are muted: dusty pink, mustard, olive, light blue. No saturated red, no deep blue, no skin tone.

Ra is the arithmetic mean of the eight individual scores, scaled so that a perfect match scores 100. That averaging is where the trouble starts. A lamp can score 95 on R1 to R8 and 8 on R9, the saturated red sample, and still report Ra 92. On a hotel project that lamp will flatten the colour of wood veneer, make tomato-based dishes look brown, and give dark skin a grey cast under close inspection.

RaTypical R9Where it is acceptableWhere it fails
800–15Corridors, plant rooms, car parks, laundryGuestrooms, restaurants, retail display
9025–50General guestroom and public-area lightingFeature walls, food, premium retail
9550–90Restaurants, bars, retail, artwork, vanityUsually unnecessary in back of house

Ra also loses resolution at the top of the scale. The difference between Ra 95 and Ra 98 is visually small; the difference between R9 20 and R9 60 is obvious on any red surface at close range. That is why specifiers in hospitality increasingly write Ra and R9 as separate requirements rather than accepting a single CRI figure.

Measurement matters as much as the number. A CRI figure comes from a spectroradiometer in an integrating sphere, taken after the fixture has stabilised — usually 30 minutes at 25 °C ambient. A report issued from a bare LED board on a bench, before the optic and diffuser are fitted, will not describe the light that reaches the wall. Optics absorb short wavelengths, diffusers shift colour, and both change the final spectrum.

One more limit: CRI is defined only for sources close to the blackbody or daylight locus. Deeply tinted or narrow-band sources can score well and look wrong. This is the gap TM-30 was written to close, and it is covered in more detail in what CRI actually measures.

3. TM-30: Rf, Rg and the color vector graphic

IES TM-30 was published in 2015 and revised as TM-30-20. It replaces eight samples with 99 colour evaluation samples drawn from real objects — textiles, skin, foliage, paint, food — and it reports two headline numbers instead of one.

Rf is fidelity, 0 to 100, averaged across all 99 samples. It works like Ra but without the pastel bias. Rg is gamut: the area of colour space the source renders compared with the reference. Rg 100 means the gamut matches; above 105 means colours are pushed and look more saturated than life; below 95 means they look washed out.

The third output is the colour vector graphic, a 16-bin map of hue shifts. Each bin, reported as Rcs, shows whether that hue family is pushed or muted. A good 3000 K source for a restaurant typically shows a slightly expanded red bin (Rcs above 100) and near-neutral bins elsewhere. A source with a cyan dip shows the opposite: a collapsed bin around 490 nm, which is what makes white linen look dingy.

ReadingWhat it tells youTypical cause
Rf 92, Rg 100Accurate, neutral, safe defaultBroadband phosphor mix with adequate red
Rf 88, Rg 105Slightly saturated, flattering on food and woodRed-enhanced phosphor
Rf 95, Rg 93Accurate but muted; safe on skin, dull on textilesHigh-fidelity package with low red output
Rf 78, Rg 110Visibly over-saturated, unusable in guestroomsCheap narrow-band red boost

Read Rf and Rg together, never separately. A high Rf with an Rg far from 100 is still a colour cast, just a smooth one. The vector graphic tells you which direction the cast runs, which is the part that matters when the client says the room looks “off” but cannot say how.

The vector graphic also settles arguments that Rf cannot. If a client says the blue-grey carpet reads purple, look at the bin around 470 nm; a positive shift there explains it, and no amount of Rf will. If white shirts look yellow in photographs, the 570–580 nm bins are the place to look. Photographers and retail visual merchandisers care about those two regions more than they care about the headline number.

Watch two things in TM-30 data. First, Rf is measured against a reference of the same CCT, so an Rf 90 at 2700 K and an Rf 90 at 4000 K describe different spectra — do not read them as interchangeable quality. Second, some suppliers publish Rf from a 3000 K test unit and ship 2700 K product; the bin matters. Ask for the report at the CCT you are buying.

Compare the two systems side by side in CRI versus TM-30, including how to read a full report page.

4. CCT and the warm-white range for hospitality

Correlated colour temperature describes where a white source sits on the warm-to-cool axis, measured in kelvin. It says nothing about how well colours render. A 2700 K lamp and a 4000 K lamp can both be Ra 90, and they will still make the same oak floor look like two different materials.

CCTCharacterWhere it belongsMaintained illuminance
2700 KWarm, close to incandescentGuestrooms, restaurants, bars, lobbies after dark100 lx general, 300 lx bedside
3000 KWarm white, close to halogenBathrooms, corridors, retail general300 lx bathroom, 100 lx corridor
3500 KNeutral warmMeeting rooms, open office, spa treatment500 lx meeting, 500 lx office
4000 KNeutralKitchens, laundry, back of house, car parks500 lx kitchen work plane

The hospitality band is narrow by design: 2700 K to 3000 K across guest-facing areas, with a tolerance of no more than 300 K between fixtures inside one view. Go wider and the eye reads the difference as dirt rather than as warmth — one wall looks yellowed, the next looks cold, and no amount of cleaning fixes it.

Colour temperature also moves when the fixture dims, and not all drivers behave the same way. A constant-current driver holds the CCT and simply reduces output; a dim-to-warm driver deliberately shifts the spectrum toward amber; a poor driver drifts by accident, typically 200–400 K downward by the time it reaches 5% output. On a scheme that mixes all three behaviours, the room turns patchy after dark, which is when guests are most likely to notice.

There is a real cost to going warm. Dropping from 3000 K to 2700 K costs roughly 5% of perceived brightness at the same lumen output, so a 2700 K scheme needs 5–10% more delivered lux to feel equally bright. Budget for it in the load calculation rather than discovering it at commissioning. The full comparison is in 2700 K versus 3000 K.

5. SDCM: why 3-step and 5-step look different

SDCM stands for standard deviation of colour matching. It counts how many MacAdam ellipses a fixture’s actual colour point sits away from its nominal CCT. One ellipse is roughly the threshold at which a trained observer notices a difference in a side-by-side comparison, so a 3-step bin covers an area three ellipses wide.

In CIE 1976 u′v′ terms, a 3-step bin at 3000 K spans roughly 0.004 in chromaticity distance, and a 5-step bin roughly 0.007. Those numbers are small on paper. On a 12 m corridor ceiling with 40 downlights in a row, they are the difference between a clean line of light and a run of panels where two near the middle clearly read greener.

BinningApproximate Δu′v′ spanWhere it is enoughRisk
2-step≈ 0.003Feature walls, art lighting, retail displayCost and lead time; limited stock
3-step≈ 0.004Guestrooms, corridors, restaurantsBatch drift if not tracked
5-step≈ 0.007Back of house, plant rooms, car parksVisible mismatch in continuous runs
7-step≈ 0.010Single fixtures in isolation onlyUnacceptable in any repeated array

The datasheet number is only half the story. A 3-step fixture sourced from one bin in January and another bin in June will still mismatch across a phased refurbishment, which is why batch codes matter more than the bin claim. That subject has its own treatment in SDCM and colour consistency.

Colour binning sits alongside flux and voltage binning, and the three interact. A 3-step colour bin split across two flux bins will produce a visible brightness step in a run of downlights even though every unit is within tolerance on colour. Suppliers who only quote a colour bin are quoting a third of the picture; ask for the full bin code, which normally reads as colour, flux and forward voltage in one string.

Ageing shifts colour as well. Phosphor and silicone degrade at different rates, and a fixture that starts at 3-step can drift to 5-step equivalent after 10,000 hours if the thermal design is weak. LM-80 data with TM-21 extrapolation gives a projection; a 25 °C test on a fixture that runs at 60 °C in a ceiling void does not. On a ten-year hotel cycle, that drift is the difference between one refurbishment and two.

Five-step is not automatically wrong. In a plant room nobody will notice. The mistake is accepting 5-step in a guest corridor because it was in stock, then discovering the problem after 200 fixtures are on site.

6. How to write light quality into a specification

A specification that survives procurement is a table with four columns and a verification clause. Write it once per area type, not once per project, and reuse it.

Lighting specification template with fields for color temperature, rendition, consistency and test conditions
AreaCRI / R9CCT and SDCMVerification
GuestroomRa ≥ 90, R9 ≥ 502700 K, ≤ 3-stepLM-79 report per SKU, sample approval
BathroomRa ≥ 90, R9 ≥ 503000 K, ≤ 3-stepLM-79 plus IP rating certificate
Restaurant / barRa ≥ 92, R9 ≥ 602700 K, ≤ 2-stepLM-79, TM-30 report, on-site mock-up
Retail displayRa ≥ 95, R9 ≥ 703000 K, ≤ 2-stepTM-30 with vector graphic
Back of houseRa ≥ 804000 K, ≤ 5-stepLM-79 report

Then add the clause that makes the table enforceable: reports must come from a laboratory accredited to ISO/IEC 17025, must be less than 24 months old, must state the exact driver and optic combination supplied, and must carry the batch code engraved or labelled on the fixture. A report for a bare LED board is not a report for a luminaire.

Add a mock-up clause for anything guest-facing. One bay of ceiling, the actual finish samples, the actual dimmer, viewed at 2700 K and at 10% output. Two hours in a mock-up room resolves more arguments than a week of datasheet exchange, and it is the only reliable way to judge whether R9 50 is enough for the timber veneer on that particular job.

Finally, test what arrives. Pull one fixture in twenty, measure at 100%, 50% and 1% output, and compare against the submitted report. Check for flicker at the bottom of the dimming range, where most drivers misbehave, and check colour shift between two units from different cartons. On a 200-fixture hotel job that is ten measurements and half a day.

For the wider package of hotel lighting design, from fixture selection to commissioning support, see hospitality lighting solutions.

Frequently asked questions

Is CRI 90 good enough for a hotel guestroom?

Yes, provided R9 is specified separately at 50 or above and the CCT tolerance is held to 3-step. Ra 90 with R9 below 20 will make timber and dark textiles look flat. Ra 90 with R9 at 50 reads as accurate in a room at 100–300 lx.

Can a fixture have high CRI and still look wrong?

Regularly. Ra averages eight pastel samples, so a strong red deficiency barely moves the score. A lamp at Ra 92 with R9 at 8 will render food and skin poorly. TM-30 Rf and Rg catch that failure; Ra alone does not.

Do I need both CRI and TM-30 in a specification?

For guest-facing areas, yes. Keep Ra and R9 as the enforceable minimum, since every supplier tests them, and add TM-30 Rf ≥ 90 with Rg between 97 and 103 as the quality gate. Requiring both costs nothing at tender and closes the gap either metric leaves open.

What does a 3-step SDCM mean in practice?

It means every fixture sits within three MacAdam ellipses of the nominal colour point, roughly 0.004 in CIE 1976 u′v′. In a room, adjacent fixtures are then indistinguishable to an untrained eye. 5-step is visibly looser in continuous runs.

Next step

Send the room schedule, ceiling heights and the areas where colour accuracy matters, and the team will return LM-79 and TM-30 reports for the proposed fixtures, plus a sample submission for the finishes you are actually using. Test data for a specific project starts at the capabilities page.

Christina

Hello, I’m Christina, founder of Qilux Lighting.Qilux Lighting is a China-based decorative and commercial lighting partner, working with distributors, lighting designers, system integrators, and project contractors worldwide.We support commercial and hospitality projects by translating design concepts into reliable, manufacturable lighting solutions, bridging design, production, and delivery.