Qilux Lighting

Light Quality Explained: CRI, CCT, TM-30 and SDCM

Qualidade da luz explicada: CRI, CCT, TM-30 e SDCM

Quatro números determinam se um projeto de iluminação parece intencional ou um compromisso: CRI, TM-30 Rf e Rg, CCT e SDCM. Eles respondem a quatro perguntas diferentes, e uma especificação que menciona apenas um deles deixa o fornecedor livre para não atender aos outros três. Este guia explica o que cada número mede, onde pode induzir em erro e quais valores são adequados para projetos de hotéis, restaurantes e lojas. Na maioria das vezes, as discussões sobre CRI da iluminação no local da obra são, na verdade, discussões sobre uma métrica à qual se exige uma função para a qual nunca foi concebida.

1. Os quatro números que definem a qualidade da luz

Uma fonte de luz emite um espectro. O olho transforma esse espectro em três impressões: a precisão com que as cores aparecem, o quão quente ou fria parece a luz branca e se duas luminárias do mesmo tipo parecem corresponder entre si. Os quatro números correspondem a essas impressões, e nenhum deles substitui os demais.

Overview of CRI, CCT, TM-30 and SDCM and the different light quality questions each metric addresses
MétricaPergunta a que respondeValor comum em projetosO que não contempla
CRI (Ra)Fidelidade cromática média em oito amostras de tons pastelRa ≥ 90 em áreas para hóspedes; ≥ 80 em áreas de serviçoVermelhos e azuis saturados, em particular R9
TM-30 (Rf, Rg)Fidelidade em 99 amostras e direção da gama cromáticaRf ≥ 90, Rg 97–103Publicado por menos fornecedores; sem mínimo legal
Temperatura de cor correlata (CCT)Onde o branco se situa no eixo de quente a frio2700 K em quartos de hóspedes; 3000 K em áreas públicasNada sobre fidelidade ou consistência
SDCMO quanto uma luminária se afasta do ponto nominal de CCT≤ 3 etapas, idealmente ≤ 2 etapasÓptica, comportamento de dimerização, envelhecimento

Cada linha falha à sua maneira. Uma luminária pode atingir Ra 92 e ainda deixar um bife malpassado com aspeto acinzentado, porque as oito amostras usadas no cálculo de Ra não incluem nenhum vermelho saturado. Pode estar exatamente nos 3000 K e, ainda assim, diferir em quatro passos da luminária instalada ao lado. Pode corresponder em ambos os parâmetros e, mesmo assim, produzir um anel visível na parede, porque o refletor é inadequado.

Há mais duas variáveis que devem ser consideradas, embora não apareçam na tabela. A primeira é a continuidade do espectro em torno dos 480 nm, onde os LED com conversão por fósforo frequentemente apresentam uma quebra; essa quebra manifesta-se como tons de azul-petróleo apagados e verde-oliva turvo. A segunda é o comportamento de dimerização, pois um driver que altera a temperatura de cor ou começa a cintilar com uma saída de 5% pode comprometer um bom espectro.

Se isto for mal especificado, o custo surge mais tarde. Substituir as lâmpadas de 200 downlights dos quartos após a entrega implica novas luminárias, mão de obra, equipamentos de acesso e quartos fora de serviço durante os trabalhos. Substituir 40 m de sancas de corredor porque o segundo lote apresenta um tom mais esverdeado é ainda pior, pois é necessário abrir o teto. Os números ocupam apenas algumas linhas num documento de especificações; a falha resulta num pedido de alteração contratual.

A consequência prática é simples. Peça os quatro valores numa única página por SKU, extraídos do mesmo relatório de ensaio, e considere que um fornecedor que só consegue apresentar um deles também não mediu os outros três.

2. IRC: o que Ra mede e o que deixa de fora

O IRC foi publicado pela CIE em 1965 e revisto em 1995 como CIE 13.3. Compara uma fonte de ensaio com uma fonte de referência à mesma temperatura de cor — um radiador de corpo negro abaixo dos 5000 K e a luz do dia acima desse valor — usando oito amostras de cor baseadas no sistema Munsell, de R1 a R8. Essas amostras são pouco saturadas: rosa pálido, amarelo-mostarda, verde-oliva e azul-claro. Não há vermelho saturado, azul profundo nem tons de pele.

Ra é a média aritmética das oito pontuações individuais, escalada de modo que uma correspondência perfeita tenha pontuação 100. É nessa média que começam os problemas. Uma lâmpada pode obter 95 em R1 a R8 e 8 em R9, a amostra de vermelho saturado, e ainda assim apresentar Ra 92. Num projeto hoteleiro, essa lâmpada achataria a cor do folheado de madeira, faria os pratos à base de tomate parecerem castanhos e daria à pele escura um tom acinzentado sob observação atenta.

RaR9 típicoOnde é aceitávelOnde falha
800–15Corredores, salas técnicas, parques de estacionamento, lavandariaQuartos, restaurantes, expositores comerciais
9025–50Iluminação geral de quartos e áreas públicasParedes de destaque, alimentos, comércio de gama alta
9550–90Restaurantes, bares, lojas, obras de arte, espelhos de toucadorGeralmente desnecessário nas áreas de serviço

Ra também perde capacidade de diferenciação no topo da escala. A diferença entre Ra 95 e Ra 98 é visualmente pequeno; a diferença entre R9 20 e R9 60 é óbvia em qualquer superfície vermelha a curta distância. É por isso que os especificadores do setor hoteleiro exigem cada vez mais Ra e R9 separadamente, em vez de aceitarem um único valor de IRC.

A medição é tão importante quanto o número. O valor de IRC é obtido com um espectrorradiômetro numa esfera integradora, depois de a luminária estabilizar — geralmente durante 30 minutos a uma temperatura ambiente de 25 °C. Um relatório emitido com base numa placa de LED nua, medida numa bancada antes da instalação da óptica e do difusor, não descreve a luz que chega à parede. A óptica absorve comprimentos de onda curtos, os difusores alteram a cor, e ambos modificam o espectro final.

Há mais uma limitação: o IRC é definido apenas para fontes próximas do locus do corpo negro ou da luz do dia. Fontes intensamente coloridas ou de banda estreita podem obter uma boa pontuação e, ainda assim, parecer inadequadas. Esta é a lacuna que a TM-30 foi criada para preencher, e o tema é abordado com mais detalhe em o que o IRC realmente mede.

3. TM-30: Rf, Rg e o gráfico vetorial de cores

A IES TM-30 foi publicada em 2015 e revista como TM-30-20. Em vez de oito amostras, utiliza 99 amostras de avaliação de cores extraídas de objetos reais — tecidos, pele, folhagem, tinta e alimentos — e apresenta dois valores principais, em vez de um.

Rf é a fidelidade, numa escala de 0 a 100, calculada como média das 99 amostras. Funciona como o Ra, mas sem o viés para tons pastel. Rg is gamut: the area of colour space the source renders compared with the reference. Rg 100 means the gamut matches; above 105 means colours are pushed and look more saturated than life; below 95 means they look washed out.

The third output is the colour vector graphic, a 16-bin map of hue shifts. Each bin, reported as Rcs, shows whether that hue family is pushed or muted. A good 3000 K source for a restaurant typically shows a slightly expanded red bin (Rcs above 100) and near-neutral bins elsewhere. A source with a cyan dip shows the opposite: a collapsed bin around 490 nm, which is what makes white linen look dingy.

ReadingWhat it tells youTypical cause
Rf 92, Rg 100Accurate, neutral, safe defaultBroadband phosphor mix with adequate red
Rf 88, Rg 105Slightly saturated, flattering on food and woodRed-enhanced phosphor
Rf 95, Rg 93Accurate but muted; safe on skin, dull on textilesHigh-fidelity package with low red output
Rf 78, Rg 110Visibly over-saturated, unusable in guestroomsCheap narrow-band red boost

Read Rf and Rg together, never separately. A high Rf with an Rg far from 100 is still a colour cast, just a smooth one. The vector graphic tells you which direction the cast runs, which is the part that matters when the client says the room looks “off” but cannot say how.

The vector graphic also settles arguments that Rf cannot. If a client says the blue-grey carpet reads purple, look at the bin around 470 nm; a positive shift there explains it, and no amount of Rf will. If white shirts look yellow in photographs, the 570–580 nm bins are the place to look. Photographers and retail visual merchandisers care about those two regions more than they care about the headline number.

Watch two things in TM-30 data. First, Rf is measured against a reference of the same CCT, so an Rf 90 at 2700 K and an Rf 90 at 4000 K describe different spectra — do not read them as interchangeable quality. Second, some suppliers publish Rf from a 3000 K test unit and ship 2700 K product; the bin matters. Ask for the report at the CCT you are buying.

Compare the two systems side by side in CRI versus TM-30, including how to read a full report page.

4. CCT and the warm-white range for hospitality

Correlated colour temperature describes where a white source sits on the warm-to-cool axis, measured in kelvin. It says nothing about how well colours render. A 2700 K lamp and a 4000 K lamp can both be Ra 90, and they will still make the same oak floor look like two different materials.

Temperatura de cor correlata (CCT)CharacterWhere it belongsMaintained illuminance
2700 KWarm, close to incandescentGuestrooms, restaurants, bars, lobbies after dark100 lx general, 300 lx bedside
3000 KWarm white, close to halogenBathrooms, corridors, retail general300 lx bathroom, 100 lx corridor
3500 KNeutral warmMeeting rooms, open office, spa treatment500 lx meeting, 500 lx office
4000 KNeutralKitchens, laundry, back of house, car parks500 lx kitchen work plane

The hospitality band is narrow by design: 2700 K to 3000 K across guest-facing areas, with a tolerance of no more than 300 K between fixtures inside one view. Go wider and the eye reads the difference as dirt rather than as warmth — one wall looks yellowed, the next looks cold, and no amount of cleaning fixes it.

Colour temperature also moves when the fixture dims, and not all drivers behave the same way. A constant-current driver holds the CCT and simply reduces output; a dim-to-warm driver deliberately shifts the spectrum toward amber; a poor driver drifts by accident, typically 200–400 K downward by the time it reaches 5% output. On a scheme that mixes all three behaviours, the room turns patchy after dark, which is when guests are most likely to notice.

There is a real cost to going warm. Dropping from 3000 K to 2700 K costs roughly 5% of perceived brightness at the same lumen output, so a 2700 K scheme needs 5–10% more delivered lux to feel equally bright. Budget for it in the load calculation rather than discovering it at commissioning. The full comparison is in 2700 K versus 3000 K.

5. SDCM: why 3-step and 5-step look different

SDCM stands for standard deviation of colour matching. It counts how many MacAdam ellipses a fixture’s actual colour point sits away from its nominal CCT. One ellipse is roughly the threshold at which a trained observer notices a difference in a side-by-side comparison, so a 3-step bin covers an area three ellipses wide.

In CIE 1976 u′v′ terms, a 3-step bin at 3000 K spans roughly 0.004 in chromaticity distance, and a 5-step bin roughly 0.007. Those numbers are small on paper. On a 12 m corridor ceiling with 40 downlights in a row, they are the difference between a clean line of light and a run of panels where two near the middle clearly read greener.

BinningApproximate Δu′v′ spanWhere it is enoughRisk
2-step≈ 0.003Feature walls, art lighting, retail displayCost and lead time; limited stock
3-step≈ 0.004Guestrooms, corridors, restaurantsBatch drift if not tracked
5-step≈ 0.007Back of house, plant rooms, car parksVisible mismatch in continuous runs
7-step≈ 0.010Single fixtures in isolation onlyUnacceptable in any repeated array

The datasheet number is only half the story. A 3-step fixture sourced from one bin in January and another bin in June will still mismatch across a phased refurbishment, which is why batch codes matter more than the bin claim. That subject has its own treatment in SDCM and colour consistency.

Colour binning sits alongside flux and voltage binning, and the three interact. A 3-step colour bin split across two flux bins will produce a visible brightness step in a run of downlights even though every unit is within tolerance on colour. Suppliers who only quote a colour bin are quoting a third of the picture; ask for the full bin code, which normally reads as colour, flux and forward voltage in one string.

Ageing shifts colour as well. Phosphor and silicone degrade at different rates, and a fixture that starts at 3-step can drift to 5-step equivalent after 10,000 hours if the thermal design is weak. LM-80 data with TM-21 extrapolation gives a projection; a 25 °C test on a fixture that runs at 60 °C in a ceiling void does not. On a ten-year hotel cycle, that drift is the difference between one refurbishment and two.

Five-step is not automatically wrong. In a plant room nobody will notice. The mistake is accepting 5-step in a guest corridor because it was in stock, then discovering the problem after 200 fixtures are on site.

6. How to write light quality into a specification

A specification that survives procurement is a table with four columns and a verification clause. Write it once per area type, not once per project, and reuse it.

Lighting specification template with fields for color temperature, rendition, consistency and test conditions
AreaCRI / R9CCT and SDCMVerification
GuestroomRa ≥ 90, R9 ≥ 502700 K, ≤ 3-stepLM-79 report per SKU, sample approval
Casa de banhoRa ≥ 90, R9 ≥ 503000 K, ≤ 3-stepLM-79 plus IP rating certificate
Restaurant / barRa ≥ 92, R9 ≥ 602700 K, ≤ 2-stepLM-79, TM-30 report, on-site mock-up
Retail displayRa ≥ 95, R9 ≥ 703000 K, ≤ 2-stepTM-30 with vector graphic
Back of houseRa ≥ 804000 K, ≤ 5-stepLM-79 report

Then add the clause that makes the table enforceable: reports must come from a laboratory accredited to ISO/IEC 17025, must be less than 24 months old, must state the exact driver and optic combination supplied, and must carry the batch code engraved or labelled on the fixture. A report for a bare LED board is not a report for a luminaire.

Add a mock-up clause for anything guest-facing. One bay of ceiling, the actual finish samples, the actual dimmer, viewed at 2700 K and at 10% output. Two hours in a mock-up room resolves more arguments than a week of datasheet exchange, and it is the only reliable way to judge whether R9 50 is enough for the timber veneer on that particular job.

Finally, test what arrives. Pull one fixture in twenty, measure at 100%, 50% and 1% output, and compare against the submitted report. Check for flicker at the bottom of the dimming range, where most drivers misbehave, and check colour shift between two units from different cartons. On a 200-fixture hotel job that is ten measurements and half a day.

For the wider package of hotel lighting design, from fixture selection to commissioning support, see hospitality lighting solutions.

Frequently asked questions

Is CRI 90 good enough for a hotel guestroom?

Yes, provided R9 is specified separately at 50 or above and the CCT tolerance is held to 3-step. Ra 90 with R9 below 20 will make timber and dark textiles look flat. Ra 90 with R9 at 50 reads as accurate in a room at 100–300 lx.

Can a fixture have high CRI and still look wrong?

Regularly. Ra averages eight pastel samples, so a strong red deficiency barely moves the score. A lamp at Ra 92 with R9 at 8 will render food and skin poorly. TM-30 Rf and Rg catch that failure; Ra alone does not.

Do I need both CRI and TM-30 in a specification?

For guest-facing areas, yes. Keep Ra and R9 as the enforceable minimum, since every supplier tests them, and add TM-30 Rf ≥ 90 with Rg between 97 and 103 as the quality gate. Requiring both costs nothing at tender and closes the gap either metric leaves open.

What does a 3-step SDCM mean in practice?

It means every fixture sits within three MacAdam ellipses of the nominal colour point, roughly 0.004 in CIE 1976 u′v′. In a room, adjacent fixtures are then indistinguishable to an untrained eye. 5-step is visibly looser in continuous runs.

Next step

Send the room schedule, ceiling heights and the areas where colour accuracy matters, and the team will return LM-79 and TM-30 reports for the proposed fixtures, plus a sample submission for the finishes you are actually using. Test data for a specific project starts at the capabilities page.

Christina

Olá, sou Christina, fundadora da Qilux Lighting.A Qilux Lighting é uma parceira de iluminação decorativa e comercial sediada na China, que trabalha com distribuidores, designers de iluminação, integradores de sistemas e empreiteiros de projetos em todo o mundo. Apoiamos projetos comerciais e de hotelaria transformando conceitos de design em soluções de iluminação confiáveis e fabricáveis, conectando design, produção e entrega.

Publicação mais recente

Tem um projeto em mente?