조명 설계가 의도대로 구현되었는지, 아니면 타협의 결과처럼 보이는지를 좌우하는 네 가지 수치가 있습니다. CRI, TM-30 Rf와 Rg, CCT, SDCM입니다. 각 수치는 서로 다른 질문에 답하며, 이 중 하나만 명시한 사양서는 공급업체가 나머지 세 가지 기준을 충족하지 못해도 책임을 묻기 어렵습니다. 이 가이드에서는 각 수치가 무엇을 측정하는지, 어떤 경우 오해를 불러일으키는지, 호텔·레스토랑·리테일 프로젝트에서 어떤 값이 적절한지 살펴봅니다. 현장에서 CRI를 두고 벌어지는 조명 관련 논쟁은 대부분 애초에 그 지표가 맡도록 설계되지 않은 역할을 기대하는 데서 비롯됩니다.
1. 조명 품질을 결정하는 네 가지 수치
광원은 스펙트럼을 방출합니다. 사람의 눈은 이 스펙트럼을 세 가지 인상으로 받아들입니다. 색이 얼마나 정확하게 보이는지, 백색광이 얼마나 따뜻하거나 차갑게 보이는지, 같은 종류의 조명기구 두 대가 서로 얼마나 비슷해 보이는지입니다. 네 가지 수치는 이러한 인상에 각각 대응하며, 어느 것도 다른 수치를 대신할 수 없습니다.

| 지표 | 지표가 답하는 질문 | 일반적인 프로젝트 기준값 | 반영하지 못하는 사항 |
|---|---|---|---|
| CRI (Ra) | 8가지 파스텔 색상 샘플의 평균 색 재현성 | 객실 공간 Ra ≥ 90, 직원 전용 공간 Ra ≥ 80 | 특히 R9를 비롯한 채도 높은 빨강과 파랑 |
| TM-30 (Rf, Rg) | 99개 샘플 전반의 색 재현성과 색역의 방향 | Rf ≥ 90, Rg 97–103 | 공개하는 공급업체가 적고, 법적 최소 기준이 없음 |
| 색온도 | 백색광이 따뜻함과 차가움의 축에서 어느 지점에 위치하는지 | 객실 2700 K, 공용 공간 3000 K | 색 재현성이나 일관성에 관한 정보는 없음 |
| SDCM | 조명기구의 색온도가 지정된 CCT 지점에서 얼마나 벗어나는지 | ≤ 3단계, 이상적으로는 ≤ 2단계 | 광학 특성, 디밍 동작, 경년 변화 |
각 항목은 저마다 다른 방식으로 실패합니다. 조명기구의 Ra가 92에 도달하더라도 레어 스테이크를 잿빛으로 보이게 할 수 있습니다. Ra를 산출하는 데 사용되는 여덟 가지 샘플에는 포화 적색이 포함되지 않기 때문입니다. 색온도가 정확히 3000 K여도 바로 옆에 설치된 조명기구와 색 차이가 4단계나 날 수 있습니다. 두 가지 기준을 모두 충족하더라도 반사판이 잘못되면 벽에 눈에 띄는 링 형태의 빛이 생길 수 있습니다.
표에는 나오지 않지만 논의에 포함해야 할 변수도 두 가지 있습니다. 첫째는 480 nm 부근의 스펙트럼 연속성입니다. 형광체 변환 LED는 이 영역에서 스펙트럼이 저하되는 경우가 많으며, 그 결과 청록색은 생기 없이, 올리브색은 탁하게 보입니다. 둘째는 디밍 동작입니다. 출력 5%에서 색온도가 변하거나 깜박이기 시작하는 드라이버는 우수한 스펙트럼의 장점을 무효로 만듭니다.
잘못 선택하면 비용은 나중에 발생합니다. 인도 후 객실 다운라이트 200개를 다시 램프로 교체하려면 새 조명기구, 인건비, 작업 장비가 필요하고, 공사 중에는 객실을 판매할 수 없습니다. 두 번째 로트의 조명 색이 더 녹색으로 보여 복도 코브 조명 40 m를 교체하는 일은 더 큰 문제입니다. 천장을 열어야 하기 때문입니다. 사양서에 수치를 적는 데 드는 비용은 몇 줄에 불과하지만, 실패하면 변경 주문 비용이 발생합니다.
실무적으로 취해야 할 조치는 간단합니다. 각 SKU에 대해 네 가지 수치를 모두 동일한 시험 성적서에서 확인할 수 있도록 한 페이지에 제시해 달라고 요청하세요. 그중 하나만 제공할 수 있는 공급업체는 나머지 세 가지를 측정하지 않은 것으로 간주해야 합니다.
2. CRI: Ra가 측정하는 것과 놓치는 것
CRI는 1965년 CIE에서 발표되었으며, 1995년에 CIE 13.3으로 개정되었습니다. CRI는 시험 광원을 동일한 색온도의 기준 광원과 비교합니다. 5000 K 미만에서는 흑체 복사체를, 그 이상에서는 주광을 기준으로 삼으며, 먼셀 색상 체계에 기반한 여덟 가지 색 샘플(R1~R8)을 사용합니다. 이 샘플은 채도가 낮습니다. 탁한 분홍색, 겨자색, 올리브색, 연한 파란색 등이 포함됩니다. 포화 적색도, 짙은 파란색도, 피부색도 없습니다.
Ra는 여덟 가지 개별 점수의 산술 평균이며, 완벽하게 일치할 때 100점이 되도록 환산됩니다. 문제는 바로 이 평균화에서 시작됩니다. 램프가 R1~R8에서 95점을 받고 포화 적색 샘플인 R9에서는 8점을 받아도 Ra 92로 표시될 수 있습니다. 호텔 프로젝트에서 이런 램프를 사용하면 목재 무늬목의 색감이 밋밋해지고, 토마토를 사용한 요리는 갈색으로 보이며, 가까이서 살펴볼 때 짙은 피부색에 잿빛이 돌게 됩니다.
| Ra | 일반적인 R9 | 적합한 적용 장소 | 성능이 부족한 적용 장소 |
|---|---|---|---|
| 80 | 0–15 | 복도, 기계실, 주차장, 세탁실 | 객실, 레스토랑, 소매점 디스플레이 |
| 90 | 25–50 | 일반 객실 및 공용 공간 조명 | 포인트 벽, 식음료, 프리미엄 소매 공간 |
| 95 | 50–90 | 레스토랑, 바, 소매점, 미술품, 화장대 | 대체로 백오브하우스 공간에는 불필요 |
Ra는 척도 상단에서도 해상도가 떨어집니다. 두 값 사이의 차이는 Ra 95 및 Ra 98 시각적으로는 미미하지만, R9 20과 R9 60의 차이는 가까운 거리에서 어떤 빨간색 표면을 보더라도 뚜렷합니다. 그래서 호스피탈리티 업계의 조명 사양 작성자들은 단일 CRI 수치만 받아들이기보다 Ra와 R9를 별도 요구사항으로 점점 더 많이 명시하고 있습니다.
측정 방식은 수치만큼 중요합니다. CRI 수치는 적분구 안의 분광복사계로 측정하며, 조명기구가 안정화된 후—일반적으로 주위 온도 25°C에서 30분 후—측정합니다. 광학 부품과 확산판을 장착하기 전에 작업대 위의 LED 기판만 측정해 발행한 보고서는 벽면에 도달하는 빛을 설명하지 못합니다. 광학 부품은 단파장을 흡수하고 확산판은 색을 변화시키며, 둘 다 최종 스펙트럼에 영향을 줍니다.
또 다른 한계가 있습니다. CRI는 흑체 궤적이나 일광 궤적에 가까운 광원에 대해서만 정의됩니다. 색조가 짙거나 협대역인 광원은 높은 점수를 얻으면서도 실제로는 부자연스러워 보일 수 있습니다. 이 간극을 해소하기 위해 TM-30이 마련되었으며, 자세한 내용은 다음에서 다룹니다 CRI가 실제로 측정하는 항목.
3. TM-30: Rf, Rg 및 색 벡터 그래프
IES TM-30은 2015년에 발표되었으며 TM-30-20으로 개정되었습니다. 기존의 8개 샘플을 실제 사물—직물, 피부, 나뭇잎, 페인트, 식품 등—에서 추출한 99개 색 평가 샘플로 대체하고, 단일 수치 대신 두 가지 주요 수치를 제시합니다.
Rf 는 충실도를 나타내며, 0~100 범위의 값으로 99개 샘플 전체의 평균입니다. Ra와 유사하지만 파스텔 색상에 치우치는 경향이 없습니다. Rg is gamut: the area of colour space the source renders compared with the reference. Rg 100 means the gamut matches; above 105 means colours are pushed and look more saturated than life; below 95 means they look washed out.
The third output is the colour vector graphic, a 16-bin map of hue shifts. Each bin, reported as Rcs, shows whether that hue family is pushed or muted. A good 3000 K source for a restaurant typically shows a slightly expanded red bin (Rcs above 100) and near-neutral bins elsewhere. A source with a cyan dip shows the opposite: a collapsed bin around 490 nm, which is what makes white linen look dingy.
| Reading | What it tells you | Typical cause |
|---|---|---|
| Rf 92, Rg 100 | Accurate, neutral, safe default | Broadband phosphor mix with adequate red |
| Rf 88, Rg 105 | Slightly saturated, flattering on food and wood | Red-enhanced phosphor |
| Rf 95, Rg 93 | Accurate but muted; safe on skin, dull on textiles | High-fidelity package with low red output |
| Rf 78, Rg 110 | Visibly over-saturated, unusable in guestrooms | Cheap narrow-band red boost |
Read Rf and Rg together, never separately. A high Rf with an Rg far from 100 is still a colour cast, just a smooth one. The vector graphic tells you which direction the cast runs, which is the part that matters when the client says the room looks “off” but cannot say how.
The vector graphic also settles arguments that Rf cannot. If a client says the blue-grey carpet reads purple, look at the bin around 470 nm; a positive shift there explains it, and no amount of Rf will. If white shirts look yellow in photographs, the 570–580 nm bins are the place to look. Photographers and retail visual merchandisers care about those two regions more than they care about the headline number.
Watch two things in TM-30 data. First, Rf is measured against a reference of the same CCT, so an Rf 90 at 2700 K and an Rf 90 at 4000 K describe different spectra — do not read them as interchangeable quality. Second, some suppliers publish Rf from a 3000 K test unit and ship 2700 K product; the bin matters. Ask for the report at the CCT you are buying.
Compare the two systems side by side in CRI versus TM-30, including how to read a full report page.
4. CCT and the warm-white range for hospitality
Correlated colour temperature describes where a white source sits on the warm-to-cool axis, measured in kelvin. It says nothing about how well colours render. A 2700 K lamp and a 4000 K lamp can both be Ra 90, and they will still make the same oak floor look like two different materials.
| 색온도 | Character | Where it belongs | Maintained illuminance |
|---|---|---|---|
| 2700 K | Warm, close to incandescent | Guestrooms, restaurants, bars, lobbies after dark | 100 lx general, 300 lx bedside |
| 3000 K | Warm white, close to halogen | Bathrooms, corridors, retail general | 300 lx bathroom, 100 lx corridor |
| 3500 K | Neutral warm | Meeting rooms, open office, spa treatment | 500 lx meeting, 500 lx office |
| 4000 K | Neutral | Kitchens, laundry, back of house, car parks | 500 lx kitchen work plane |
The hospitality band is narrow by design: 2700 K to 3000 K across guest-facing areas, with a tolerance of no more than 300 K between fixtures inside one view. Go wider and the eye reads the difference as dirt rather than as warmth — one wall looks yellowed, the next looks cold, and no amount of cleaning fixes it.
Colour temperature also moves when the fixture dims, and not all drivers behave the same way. A constant-current driver holds the CCT and simply reduces output; a dim-to-warm driver deliberately shifts the spectrum toward amber; a poor driver drifts by accident, typically 200–400 K downward by the time it reaches 5% output. On a scheme that mixes all three behaviours, the room turns patchy after dark, which is when guests are most likely to notice.
There is a real cost to going warm. Dropping from 3000 K to 2700 K costs roughly 5% of perceived brightness at the same lumen output, so a 2700 K scheme needs 5–10% more delivered lux to feel equally bright. Budget for it in the load calculation rather than discovering it at commissioning. The full comparison is in 2700 K versus 3000 K.
5. SDCM: why 3-step and 5-step look different
SDCM stands for standard deviation of colour matching. It counts how many MacAdam ellipses a fixture’s actual colour point sits away from its nominal CCT. One ellipse is roughly the threshold at which a trained observer notices a difference in a side-by-side comparison, so a 3-step bin covers an area three ellipses wide.
In CIE 1976 u′v′ terms, a 3-step bin at 3000 K spans roughly 0.004 in chromaticity distance, and a 5-step bin roughly 0.007. Those numbers are small on paper. On a 12 m corridor ceiling with 40 downlights in a row, they are the difference between a clean line of light and a run of panels where two near the middle clearly read greener.
| Binning | Approximate Δu′v′ span | Where it is enough | Risk |
|---|---|---|---|
| 2-step | ≈ 0.003 | Feature walls, art lighting, retail display | Cost and lead time; limited stock |
| 3-step | ≈ 0.004 | Guestrooms, corridors, restaurants | Batch drift if not tracked |
| 5-step | ≈ 0.007 | Back of house, plant rooms, car parks | Visible mismatch in continuous runs |
| 7-step | ≈ 0.010 | Single fixtures in isolation only | Unacceptable in any repeated array |
The datasheet number is only half the story. A 3-step fixture sourced from one bin in January and another bin in June will still mismatch across a phased refurbishment, which is why batch codes matter more than the bin claim. That subject has its own treatment in SDCM and colour consistency.
Colour binning sits alongside flux and voltage binning, and the three interact. A 3-step colour bin split across two flux bins will produce a visible brightness step in a run of downlights even though every unit is within tolerance on colour. Suppliers who only quote a colour bin are quoting a third of the picture; ask for the full bin code, which normally reads as colour, flux and forward voltage in one string.
Ageing shifts colour as well. Phosphor and silicone degrade at different rates, and a fixture that starts at 3-step can drift to 5-step equivalent after 10,000 hours if the thermal design is weak. LM-80 data with TM-21 extrapolation gives a projection; a 25 °C test on a fixture that runs at 60 °C in a ceiling void does not. On a ten-year hotel cycle, that drift is the difference between one refurbishment and two.
Five-step is not automatically wrong. In a plant room nobody will notice. The mistake is accepting 5-step in a guest corridor because it was in stock, then discovering the problem after 200 fixtures are on site.
6. How to write light quality into a specification
A specification that survives procurement is a table with four columns and a verification clause. Write it once per area type, not once per project, and reuse it.

| Area | CRI / R9 | CCT and SDCM | Verification |
|---|---|---|---|
| Guestroom | Ra ≥ 90, R9 ≥ 50 | 2700 K, ≤ 3-step | LM-79 report per SKU, sample approval |
| 욕실 | Ra ≥ 90, R9 ≥ 50 | 3000 K, ≤ 3-step | LM-79 plus IP rating certificate |
| Restaurant / bar | Ra ≥ 92, R9 ≥ 60 | 2700 K, ≤ 2-step | LM-79, TM-30 report, on-site mock-up |
| 소매 매장 디스플레이 | Ra ≥ 95, R9 ≥ 70 | 3000 K, ≤ 2-step | TM-30 with vector graphic |
| Back of house | Ra ≥ 80 | 4000 K, ≤ 5-step | LM-79 report |
Then add the clause that makes the table enforceable: reports must come from a laboratory accredited to ISO/IEC 17025, must be less than 24 months old, must state the exact driver and optic combination supplied, and must carry the batch code engraved or labelled on the fixture. A report for a bare LED board is not a report for a luminaire.
Add a mock-up clause for anything guest-facing. One bay of ceiling, the actual finish samples, the actual dimmer, viewed at 2700 K and at 10% output. Two hours in a mock-up room resolves more arguments than a week of datasheet exchange, and it is the only reliable way to judge whether R9 50 is enough for the timber veneer on that particular job.
Finally, test what arrives. Pull one fixture in twenty, measure at 100%, 50% and 1% output, and compare against the submitted report. Check for flicker at the bottom of the dimming range, where most drivers misbehave, and check colour shift between two units from different cartons. On a 200-fixture hotel job that is ten measurements and half a day.
For the wider package of hotel lighting design, from fixture selection to commissioning support, see hospitality lighting solutions.
Frequently asked questions
Is CRI 90 good enough for a hotel guestroom?
Yes, provided R9 is specified separately at 50 or above and the CCT tolerance is held to 3-step. Ra 90 with R9 below 20 will make timber and dark textiles look flat. Ra 90 with R9 at 50 reads as accurate in a room at 100–300 lx.
Can a fixture have high CRI and still look wrong?
Regularly. Ra averages eight pastel samples, so a strong red deficiency barely moves the score. A lamp at Ra 92 with R9 at 8 will render food and skin poorly. TM-30 Rf and Rg catch that failure; Ra alone does not.
Do I need both CRI and TM-30 in a specification?
For guest-facing areas, yes. Keep Ra and R9 as the enforceable minimum, since every supplier tests them, and add TM-30 Rf ≥ 90 with Rg between 97 and 103 as the quality gate. Requiring both costs nothing at tender and closes the gap either metric leaves open.
What does a 3-step SDCM mean in practice?
It means every fixture sits within three MacAdam ellipses of the nominal colour point, roughly 0.004 in CIE 1976 u′v′. In a room, adjacent fixtures are then indistinguishable to an untrained eye. 5-step is visibly looser in continuous runs.
Next step
Send the room schedule, ceiling heights and the areas where colour accuracy matters, and the team will return LM-79 and TM-30 reports for the proposed fixtures, plus a sample submission for the finishes you are actually using. Test data for a specific project starts at the capabilities page.







