Quatre chiffres déterminent si un éclairage semble avoir été conçu avec soin ou s’il relève du compromis : le CRI, le TM-30 Rf et Rg, la CCT et le SDCM. Ils répondent à quatre questions différentes ; une spécification qui n’en mentionne qu’un seul laisse au fournisseur toute latitude pour ne pas respecter les trois autres. Ce guide explique ce que mesure chaque chiffre, en quoi il peut être trompeur et quelles valeurs donnent de bons résultats dans les projets hôteliers, de restauration et de commerce de détail. Sur les chantiers, la plupart des débats sur l’éclairage et le CRI portent en réalité sur un indicateur auquel on demande de remplir une fonction pour laquelle il n’a jamais été conçu.
1. Les quatre chiffres qui définissent la qualité de la lumière
Une source lumineuse émet un spectre. L’œil traduit ce spectre en trois impressions : la fidélité d’apparence des couleurs, la tonalité chaude ou froide du blanc et la capacité de deux luminaires de même type à paraître identiques. Les quatre chiffres correspondent à ces impressions, et aucun ne remplace les autres.

| Indicateur | Question à laquelle il répond | Valeur courante dans les projets | Ce qu’il ne prend pas en compte |
|---|---|---|---|
| CRI (Ra) | Fidélité moyenne des couleurs sur huit échantillons pastel | Ra ≥ 90 dans les espaces réservés aux clients, ≥ 80 dans les espaces de service | Les rouges et les bleus saturés, notamment R9 |
| TM-30 (Rf, Rg) | Fidélité sur 99 échantillons et direction du gamut | Rf ≥ 90, Rg 97–103 | Publié par un nombre plus restreint de fournisseurs ; aucun minimum légal |
| Température de couleur | Où se situe le blanc sur l’axe chaud-froid | 2700 K dans les chambres, 3000 K dans les espaces publics | Ni la fidélité ni la régularité |
| SDCM | Écart entre un luminaire et son point de CCT nominal | ≤ 3 étapes, idéalement ≤ 2 | Optique, comportement de variation, vieillissement |
Chaque ligne présente ses propres défauts. Un luminaire peut atteindre un Ra de 92 et pourtant griser un steak saignant, car les huit échantillons pris en compte dans le Ra ne contiennent aucun rouge saturé. Il peut afficher exactement 3 000 K et pourtant présenter un écart de quatre paliers avec le luminaire installé juste à côté. Il peut correspondre sur ces deux critères et malgré tout créer un anneau visible sur un mur, parce que le réflecteur n’est pas adapté.
Deux autres variables doivent être prises en compte, même si elles ne figurent pas dans le tableau. La première est la continuité du spectre autour de 480 nm, où les LED à conversion par phosphore présentent souvent un creux ; celui-ci se traduit par des tons bleu-vert ternes et des tons olive brouillés. La seconde est le comportement de variation, car un driver qui modifie la température de couleur ou commence à scintiller à 5 % de puissance annulera les bénéfices d’un bon spectre.
Si l’on se trompe, les coûts se manifestent tardivement. Remplacer les lampes de 200 downlights dans les chambres après la réception implique de nouveaux luminaires, de la main-d’œuvre, du matériel d’accès et des chambres indisponibles pendant les travaux. Remplacer 40 m de corniche lumineuse dans un couloir parce que le deuxième lot paraît plus vert est encore pire, car il faut ouvrir le plafond. Les chiffres ne prennent que quelques lignes dans un document de spécification ; l’échec, lui, entraîne un ordre de modification.
La conséquence pratique est simple. Demandez que les quatre chiffres figurent sur une seule page par référence, dans un même rapport d’essai, et considérez qu’un fournisseur qui ne peut en communiquer qu’un seul n’a pas mesuré les trois autres.
2. IRC : ce que mesure le Ra et ce qu’il ne mesure pas
L’IRC a été publié par la CIE en 1965, puis révisé en 1995 sous la référence CIE 13.3. Il compare une source d’essai à une source de référence de même température de couleur — un radiateur à corps noir en dessous de 5 000 K, la lumière du jour au-dessus — à l’aide de huit échantillons de couleur inspirés du système Munsell, de R1 à R8. Ces échantillons sont peu saturés : rose poudré, moutarde, olive, bleu clair. Aucun rouge saturé, aucun bleu profond, aucune teinte de peau.
Le Ra est la moyenne arithmétique des huit scores individuels, ramenée à une échelle où une correspondance parfaite vaut 100. C’est là que les problèmes commencent. Une lampe peut obtenir 95 pour R1 à R8 et 8 pour R9, l’échantillon rouge saturé, tout en affichant un Ra de 92. Dans un projet hôtelier, cette lampe aplatira la couleur des placages en bois, fera paraître bruns les plats à base de tomate et donnera aux peaux foncées une nuance grise lors d’un examen rapproché.
| Ra | R9 typique | Où cela est acceptable | Où cela pose problème |
|---|---|---|---|
| 80 | 0–15 | Couloirs, locaux techniques, parkings, blanchisserie | Chambres, restaurants, présentoirs de vente au détail |
| 90 | 25–50 | Éclairage général des chambres et des espaces publics | Murs d’accent, aliments, vente au détail haut de gamme |
| 95 | 50–90 | Restaurants, bars, vente au détail, œuvres d’art, miroirs de maquillage | Généralement inutile dans les zones réservées au personnel |
Le Ra perd également en précision dans le haut de l’échelle. La différence entre Ra 95 et Ra 98 est visuellement faible ; la différence entre R9 20 et R9 60 est évidente sur toute surface rouge à courte distance. C’est pourquoi les prescripteurs du secteur hôtelier indiquent de plus en plus Ra et R9 comme exigences distinctes, au lieu de se contenter d’une seule valeur de CRI.
La mesure compte autant que le chiffre. Une valeur de CRI est obtenue à l’aide d’un spectroradiomètre placé dans une sphère intégrante, après stabilisation du luminaire — généralement pendant 30 minutes à une température ambiante de 25 °C. Un rapport établi à partir d’une carte LED nue, sur un banc d’essai et avant la pose de l’optique et du diffuseur, ne décrit pas la lumière qui atteint le mur. Les optiques absorbent les courtes longueurs d’onde, les diffuseurs modifient la couleur, et les deux changent le spectre final.
Une autre limite : le CRI est défini uniquement pour les sources proches du lieu du corps noir ou de la lumière du jour. Les sources fortement teintées ou à bande étroite peuvent obtenir un bon score tout en produisant un rendu inadéquat. C’est cette lacune que la norme TM-30 a été conçue pour combler, et elle est abordée plus en détail dans ce que mesure réellement le CRI.
3. TM-30 : Rf, Rg et le graphique des vecteurs de couleur
La norme IES TM-30 a été publiée en 2015, puis révisée sous le nom de TM-30-20. Elle remplace les huit échantillons par 99 échantillons d’évaluation des couleurs tirés d’objets réels — textiles, peau, feuillage, peinture, aliments — et fournit deux valeurs principales au lieu d’une seule.
Rf est la fidélité, sur une échelle de 0 à 100, calculée en moyenne sur les 99 échantillons. Cette mesure fonctionne comme Ra, mais sans le biais en faveur des couleurs pastel. Rg is gamut: the area of colour space the source renders compared with the reference. Rg 100 means the gamut matches; above 105 means colours are pushed and look more saturated than life; below 95 means they look washed out.
The third output is the colour vector graphic, a 16-bin map of hue shifts. Each bin, reported as Rcs, shows whether that hue family is pushed or muted. A good 3000 K source for a restaurant typically shows a slightly expanded red bin (Rcs above 100) and near-neutral bins elsewhere. A source with a cyan dip shows the opposite: a collapsed bin around 490 nm, which is what makes white linen look dingy.
| Reading | What it tells you | Typical cause |
|---|---|---|
| Rf 92, Rg 100 | Accurate, neutral, safe default | Broadband phosphor mix with adequate red |
| Rf 88, Rg 105 | Slightly saturated, flattering on food and wood | Red-enhanced phosphor |
| Rf 95, Rg 93 | Accurate but muted; safe on skin, dull on textiles | High-fidelity package with low red output |
| Rf 78, Rg 110 | Visibly over-saturated, unusable in guestrooms | Cheap narrow-band red boost |
Read Rf and Rg together, never separately. A high Rf with an Rg far from 100 is still a colour cast, just a smooth one. The vector graphic tells you which direction the cast runs, which is the part that matters when the client says the room looks “off” but cannot say how.
The vector graphic also settles arguments that Rf cannot. If a client says the blue-grey carpet reads purple, look at the bin around 470 nm; a positive shift there explains it, and no amount of Rf will. If white shirts look yellow in photographs, the 570–580 nm bins are the place to look. Photographers and retail visual merchandisers care about those two regions more than they care about the headline number.
Watch two things in TM-30 data. First, Rf is measured against a reference of the same CCT, so an Rf 90 at 2700 K and an Rf 90 at 4000 K describe different spectra — do not read them as interchangeable quality. Second, some suppliers publish Rf from a 3000 K test unit and ship 2700 K product; the bin matters. Ask for the report at the CCT you are buying.
Compare the two systems side by side in CRI versus TM-30, including how to read a full report page.
4. CCT and the warm-white range for hospitality
Correlated colour temperature describes where a white source sits on the warm-to-cool axis, measured in kelvin. It says nothing about how well colours render. A 2700 K lamp and a 4000 K lamp can both be Ra 90, and they will still make the same oak floor look like two different materials.
| Température de couleur | Character | Where it belongs | Maintained illuminance |
|---|---|---|---|
| 2700 K | Warm, close to incandescent | Guestrooms, restaurants, bars, lobbies after dark | 100 lx general, 300 lx bedside |
| 3000 K | Warm white, close to halogen | Bathrooms, corridors, retail general | 300 lx bathroom, 100 lx corridor |
| 3500 K | Neutral warm | Meeting rooms, open office, spa treatment | 500 lx meeting, 500 lx office |
| 4000 K | Neutral | Kitchens, laundry, back of house, car parks | 500 lx kitchen work plane |
The hospitality band is narrow by design: 2700 K to 3000 K across guest-facing areas, with a tolerance of no more than 300 K between fixtures inside one view. Go wider and the eye reads the difference as dirt rather than as warmth — one wall looks yellowed, the next looks cold, and no amount of cleaning fixes it.
Colour temperature also moves when the fixture dims, and not all drivers behave the same way. A constant-current driver holds the CCT and simply reduces output; a dim-to-warm driver deliberately shifts the spectrum toward amber; a poor driver drifts by accident, typically 200–400 K downward by the time it reaches 5% output. On a scheme that mixes all three behaviours, the room turns patchy after dark, which is when guests are most likely to notice.
There is a real cost to going warm. Dropping from 3000 K to 2700 K costs roughly 5% of perceived brightness at the same lumen output, so a 2700 K scheme needs 5–10% more delivered lux to feel equally bright. Budget for it in the load calculation rather than discovering it at commissioning. The full comparison is in 2700 K versus 3000 K.
5. SDCM: why 3-step and 5-step look different
SDCM stands for standard deviation of colour matching. It counts how many MacAdam ellipses a fixture’s actual colour point sits away from its nominal CCT. One ellipse is roughly the threshold at which a trained observer notices a difference in a side-by-side comparison, so a 3-step bin covers an area three ellipses wide.
In CIE 1976 u′v′ terms, a 3-step bin at 3000 K spans roughly 0.004 in chromaticity distance, and a 5-step bin roughly 0.007. Those numbers are small on paper. On a 12 m corridor ceiling with 40 downlights in a row, they are the difference between a clean line of light and a run of panels where two near the middle clearly read greener.
| Binning | Approximate Δu′v′ span | Where it is enough | Risk |
|---|---|---|---|
| 2-step | ≈ 0.003 | Feature walls, art lighting, retail display | Cost and lead time; limited stock |
| 3-step | ≈ 0.004 | Guestrooms, corridors, restaurants | Batch drift if not tracked |
| 5-step | ≈ 0.007 | Back of house, plant rooms, car parks | Visible mismatch in continuous runs |
| 7-step | ≈ 0.010 | Single fixtures in isolation only | Unacceptable in any repeated array |
The datasheet number is only half the story. A 3-step fixture sourced from one bin in January and another bin in June will still mismatch across a phased refurbishment, which is why batch codes matter more than the bin claim. That subject has its own treatment in SDCM and colour consistency.
Colour binning sits alongside flux and voltage binning, and the three interact. A 3-step colour bin split across two flux bins will produce a visible brightness step in a run of downlights even though every unit is within tolerance on colour. Suppliers who only quote a colour bin are quoting a third of the picture; ask for the full bin code, which normally reads as colour, flux and forward voltage in one string.
Ageing shifts colour as well. Phosphor and silicone degrade at different rates, and a fixture that starts at 3-step can drift to 5-step equivalent after 10,000 hours if the thermal design is weak. LM-80 data with TM-21 extrapolation gives a projection; a 25 °C test on a fixture that runs at 60 °C in a ceiling void does not. On a ten-year hotel cycle, that drift is the difference between one refurbishment and two.
Five-step is not automatically wrong. In a plant room nobody will notice. The mistake is accepting 5-step in a guest corridor because it was in stock, then discovering the problem after 200 fixtures are on site.
6. How to write light quality into a specification
A specification that survives procurement is a table with four columns and a verification clause. Write it once per area type, not once per project, and reuse it.

| Area | CRI / R9 | CCT and SDCM | Verification |
|---|---|---|---|
| Guestroom | Ra ≥ 90, R9 ≥ 50 | 2700 K, ≤ 3-step | LM-79 report per SKU, sample approval |
| Salle de bains | Ra ≥ 90, R9 ≥ 50 | 3000 K, ≤ 3-step | LM-79 plus IP rating certificate |
| Restaurant / bar | Ra ≥ 92, R9 ≥ 60 | 2700 K, ≤ 2-step | LM-79, TM-30 report, on-site mock-up |
| Retail display | Ra ≥ 95, R9 ≥ 70 | 3000 K, ≤ 2-step | TM-30 with vector graphic |
| Back of house | Ra ≥ 80 | 4000 K, ≤ 5-step | LM-79 report |
Then add the clause that makes the table enforceable: reports must come from a laboratory accredited to ISO/IEC 17025, must be less than 24 months old, must state the exact driver and optic combination supplied, and must carry the batch code engraved or labelled on the fixture. A report for a bare LED board is not a report for a luminaire.
Add a mock-up clause for anything guest-facing. One bay of ceiling, the actual finish samples, the actual dimmer, viewed at 2700 K and at 10% output. Two hours in a mock-up room resolves more arguments than a week of datasheet exchange, and it is the only reliable way to judge whether R9 50 is enough for the timber veneer on that particular job.
Finally, test what arrives. Pull one fixture in twenty, measure at 100%, 50% and 1% output, and compare against the submitted report. Check for flicker at the bottom of the dimming range, where most drivers misbehave, and check colour shift between two units from different cartons. On a 200-fixture hotel job that is ten measurements and half a day.
For the wider package of hotel lighting design, from fixture selection to commissioning support, see hospitality lighting solutions.
Frequently asked questions
Is CRI 90 good enough for a hotel guestroom?
Yes, provided R9 is specified separately at 50 or above and the CCT tolerance is held to 3-step. Ra 90 with R9 below 20 will make timber and dark textiles look flat. Ra 90 with R9 at 50 reads as accurate in a room at 100–300 lx.
Can a fixture have high CRI and still look wrong?
Regularly. Ra averages eight pastel samples, so a strong red deficiency barely moves the score. A lamp at Ra 92 with R9 at 8 will render food and skin poorly. TM-30 Rf and Rg catch that failure; Ra alone does not.
Do I need both CRI and TM-30 in a specification?
For guest-facing areas, yes. Keep Ra and R9 as the enforceable minimum, since every supplier tests them, and add TM-30 Rf ≥ 90 with Rg between 97 and 103 as the quality gate. Requiring both costs nothing at tender and closes the gap either metric leaves open.
What does a 3-step SDCM mean in practice?
It means every fixture sits within three MacAdam ellipses of the nominal colour point, roughly 0.004 in CIE 1976 u′v′. In a room, adjacent fixtures are then indistinguishable to an untrained eye. 5-step is visibly looser in continuous runs.
Next step
Send the room schedule, ceiling heights and the areas where colour accuracy matters, and the team will return LM-79 and TM-30 reports for the proposed fixtures, plus a sample submission for the finishes you are actually using. Test data for a specific project starts at the capabilities page.







