Qilux Lighting

IP Ratings for Lighting: The Complete Guide

IP Ratings for Lighting: The Complete Guide

An IP rating answers two questions and only two: can a solid get in, and what happens when water arrives. IEC 60529 defines both digits, and almost every lighting datasheet in a hotel tender quotes them. The trouble starts when a supplier writes “IP44” for a fitting whose only protected part is the front lens, while the cable entry at the back is open. This guide walks the scale from IP20 to IP68, marks the four ratings that cover most hotel work, and lists what to ask for before a submittal is approved.

1. What the two IP digits mean

IP stands for Ingress Protection, and the number is written as two digits: IP followed by the solid figure, then the liquid figure. IP65 is not “better than” IP44 in every direction — it is a different pair of test results. A fitting can be dust tight and still fail a splash test if its gasket sits on the wrong face.

IP code diagram separating protection against solid objects, water ingress and unspecified test ratings

The first digit runs 0 to 6. It measures resistance to solid objects, from a 50 mm sphere at 0 up to complete dust tightness at 6. The important threshold for lighting is 5: at IP5X the ingress is limited but not eliminated, so dust can still enter and settle on the LED board. Only 6 is dust tight, and only 6 is worth claiming for a ceiling void with fibrous insulation blowing around.

The second digit runs 0 to 8. It starts at vertical drips and ends at continuous immersion. Note what is absent: there is no digit for condensation, no digit for salt, and no digit for water vapour moving through a warm luminaire into a cold ceiling. Those are the three failure modes most often seen in the field, and the IP number says nothing about any of them.

DigitFirst digit: solidsSecond digit: water
0No protectionNo protection
1≥ 50 mm objects (a hand)Vertical drips
2≥ 12.5 mm (a finger)Drips with enclosure tilted 15°
3≥ 2.5 mm (a tool, a thick wire)Spray up to 60° from vertical
4≥ 1.0 mm (a thin wire, a screw)Splashing from any direction
5Dust protected, not dust tightWater jets, 6.3 mm nozzle
6Dust tightPowerful jets, 12.5 mm nozzle
7—Immersion 1 m for 30 min
8—Immersion beyond 1 m, by agreement

An “X” in either position means the fitting was not tested for that condition, not that it passed. IPX4 on a bathroom mirror light is common and legitimate: the manufacturer tested water only. If you need dust protection as well, write IP44, not IPX4.

2. IP20 to IP68: what each level survives

Most of the scale is irrelevant to hotel work. Six ratings carry almost every specification, and knowing where each one stops is more useful than memorising all of them.

IP20 is a dry interior fitting: no dust test, no water test. It is correct for a guestroom ceiling, a corridor downlight and a ballroom pendant, provided the ceiling is dry and the plenum is not used as a return-air path for a kitchen. IP23 adds spray at 60° from vertical, which suits a canopy soffit where wind-driven rain reaches the underside but not the sides.

IP44 is the workhorse of bathrooms and covered terraces: 1 mm solids and splashing water from any direction, tested for five minutes at 10 litres per minute. It is the minimum for zone 1 and zone 2 of a bathroom under IEC 60364-7-701, and the sensible default for a hotel balcony with a roof over it.

IP54 and IP55 add dust protection and a jet. IP54 is dust protected and splash rated; IP55 is dust protected and jet rated at 6.3 mm. Car park soffits, service corridors, kitchen back-of-house and plant rooms sit here. Anything within reach of a pressure washer needs IP55 at minimum, and IP65 if the nozzle will come within a metre.

IP65 and IP66 are dust tight with a jet. IP65 is the baseline for exposed terraces, pool surrounds, garden path lights and façade uplights. IP66 takes the larger 12.5 mm nozzle at 100 litres per minute, which is what a washdown bay or a commercial kitchen wall actually sees.

IP66 is not a marketing upgrade of IP65. The 12.5 mm nozzle delivers eight times the flow of the 6.3 mm one, and it is the test that separates a fitting designed for a washdown wall from one that merely has a rubber ring. If housekeeping uses a pressure washer anywhere near the fixture, specify IP66 and check the cable gland, because the gland is where the water actually gets in.

IP67 and IP68 are immersion. IP67 means 1 m for 30 minutes; IP68 means deeper or longer, as agreed between buyer and maker, so the datasheet must state the depth and duration or the number is meaningless. Pool niche lights, fountain fixtures and step lights in a water feature live here. An IP68 fitting with a 0.5 m cable tail and a connector above water is only IP68 up to the connector.

3. Water jets vs immersion: IPX5, IPX6, IPX7

The three ratings are tested with different rigs, and passing one tells you almost nothing about the others. This is the single most common misunderstanding in a submittal review.

TestMethodWhat it provesWhat it does not prove
IPX4Oscillating spray, 10 L/min, 5 min, 360°No harmful ingress from splashesNothing about standing water
IPX56.3 mm nozzle, 12.5 L/min, 3 min, 3 mResists a directed low-pressure jetNothing about immersion
IPX612.5 mm nozzle, 100 L/min, 3 min, 3 mResists a heavy jet, e.g. washdownNothing about immersion
IPX7Immersion 1 m, 30 minNo ingress at 1 m static headNothing about jets or pressure
IPX8Immersion, depth and time by agreementWhatever the datasheet statesAnything not stated

A jet at 12.5 litres per minute hits the gasket with dynamic pressure; immersion pushes on it with static head. A gasket that seals under a jet can lift under 1 m of water if it is only compressed on one edge. Conversely, a potted IP67 fixture with no drainage path will hold water inside after a jet test if the cable gland is the weak point.

For a hotel, the practical rule is: if the fitting will be hosed, specify IP65 or IP66 and check the gland. If it will sit under water, specify IP67 or IP68 and check the cable length and connector rating. Do not accept “IP65, so it can go in the pool”.

4. Where hotels need which rating

The table below is the one I use at design stage. It is deliberately conservative: the cost difference between IP44 and IP65 on a downlight is small, and the cost of replacing 60 corroded fittings in year three is not.

LocationMinimum IPReason
Guestroom, corridor, lobby (dry ceiling)IP20No water source; dust only from construction
Bathroom zone 1 and 2 (per IEC 60364-7-701)IPX4, IPX5 if a shower head can spray it directlySplash and, in public bathrooms, cleaning hoses
Bathroom zone 0 (inside the tub or shower tray)IPX7, SELV 12 VImmersion plus shock risk
Covered terrace, loggia, balcony with soffitIP44Wind-driven rain reaches the underside only
Exposed terrace, pool deck, garden pathIP65, IK08 for path lightsRain, jets from cleaning, occasional knocks
Commercial kitchen, dishwash, laundryIP65, IP66 at the washdown wallSteam, grease, pressure washing
Spa, steam room, pool hall ceilingIP65, corrosion class C4Chlorinated vapour condenses on cold metal
Pool underwater nicheIP68, depth statedPermanent immersion
Car park soffit, service corridorIP54 to IP55Dust, damp, occasional hose-down
Façade uplight, sign lightingIP65 to IP66Rain and wind-driven water at height

Two ratings on this table are commonly under-specified. The first is the pool hall ceiling: it is not underwater, so teams specify IP44, and then the chlorinated vapour destroys the finish in eighteen months. The second is the bathroom in a public building, where housekeeping sprays a hose at the wall. That is a jet, not a splash, and IPX4 will not hold.

Where the rating is genuinely marginal, choose the higher one and spend the difference on a better gasket and a stainless fixing screw. The screws are what fail first in a wet ceiling.

5. IP is not UV, salt or impact resistance

An IP number describes water and solids entering an enclosure. It says nothing about the enclosure surviving the environment it sits in. Four failures sit entirely outside its scope.

Comparison of ingress protection, corrosion resistance, UV resistance and impact resistance

Corrosion. A die-cast aluminium body with a powder coat can be IP65 and still chalk, blister and pit within two summers at a coastal site. ISO 9223 classifies corrosivity from C1 (indoor dry) to C5 (marine) and CX (offshore); a beachfront resort is C5, and a fitting for it needs 316L stainless or a marine-grade coating system, and not a gasket alone. Salt spray testing to ISO 9227 for 480 hours is the usual evidence, and 720 hours is a reasonable ask for a C5 site.

UV. Polycarbonate diffusers yellow and embrittle under UV unless stabilised. A stamped “UV-stabilised PC” claim without a test is worth little; ask for the material grade and the hours of QUV or xenon-arc exposure. Powder coat on a south-facing façade in Dubai or Queensland will chalk unless it is a polyester or PVDF system rated for exterior exposure.

Impact. That is IK, governed by IEC 62262, and it is a separate number. A decorative bollard can be IP65 and IK05, and one knock from a maintenance cart ends it. Path lights and anything at trolley height should be IK08 or better.

Condensation. A sealed IP65 luminaire in a humid space traps moisture that entered during installation. When the light is on the air expands, when it is off the water condenses on the coldest surface — usually the driver or the LED board. This is why good wet-area fittings have a breather valve or a Gore vent, and why “more sealed” is not automatically “more reliable”.

The thermal cost is measurable. Closing the same 15 W downlight from IP20 to IP65 typically raises the driver case temperature by 8–12 K, because the housing that keeps water out also keeps heat in. Electrolytic capacitor life roughly halves for every 10 K rise, so a driver rated 50,000 hours at 60 °C may deliver 25,000 hours at 70 °C. On a hotel with 400 bathroom fittings, that is the difference between a ten-year life and a five-year replacement round.

Finally, read where the rating applies. A front-frame IP44 with an open back plate is an IP44 lens, not an IP44 luminaire. Recessed fittings must be rated for the void they sit in, and a fire-rated downlight in a bathroom ceiling needs its IP declared for the whole body, including the connector block.

6. Testing and certificates to ask for

An IP claim is a type-test result, not a routine production check. Nobody immerses every fixture before shipping. So the evidence you collect at approval stage is the only thing standing between you and a batch that leaks.

Ask for the test report, not the certificate. A certificate of compliance is a one-page statement; the report shows the laboratory, the standard (IEC 60529, or EN 60529 which is identical), the sample configuration and the pass criteria. Check four things in it:

  • The report names the exact model and variant you are buying. A family certificate covering twelve sizes is common, and the smallest size often has the thinnest gasket.
  • The sample was tested as installed: cable gland fitted, driver in place, diffuser on. Reports tested with a blanking plate are not evidence for the delivered product.
  • The second digit was actually tested. IPX4 and “suitable for bathrooms” are not the same statement.
  • The date and the laboratory are identifiable, and the lab is accredited for IEC 60529.

Then ask the factory two process questions. Is the gasket compression set by torque or by hand, and is the torque written on the work instruction? Is every unit given a short IP check on the gasket seat, or only a visual? A supplier who can answer both is controlling the variable that actually causes failures.

For projects in the EU and UK, IP sits alongside CE or UKCA marking, RoHS 2011/65/EU and the energy label under EU 2019/2020, all of which are set out in our compliance and sustainability notes. An IP report does not substitute for any of them, and a CE declaration that lists IP65 for a fitting whose report says IP44 is a documentation error worth escalating.

Frequently asked questions

Is a higher IP rating always better?

No. A fully sealed IP65 fitting in a dry ceiling costs more, runs hotter and can trap moisture that a ventilated IP20 body would release. Higher ratings also tend to mean bonded lenses that are harder to service. Specify the rating the location needs, plus one step of margin where cleaning practice is uncertain.

Can I use an IP65 light in a bathroom zone 1?

Yes, IP65 exceeds the IPX4 minimum for zone 1, provided the fitting is also suitable for the zone’s shock protection requirements. In zone 1 that usually means SELV at 12 V or a 30 mA RCD-protected circuit, and the fitting must be rated for the ambient temperature of a steamy room.

Does IP44 mean the fitting can go outdoors?

Only under cover. IP44 is splash rated, so a soffit or a balcony with a roof above is fine. Direct rain at an angle, wind-driven spray and standing water are outside its test, and so is UV. For an exposed position, IP65 plus a corrosion class appropriate to the site is the starting point.

What does the X in IPX4 mean?

It means the solid-particle digit was not tested, not that the fitting failed. Many bathroom fittings are legitimately sold as IPX4 because only water ingress matters there. If dust is also a concern, for example in a ceiling void with loose insulation, specify IP44 or IP54 instead.

How often should IP ratings be re-verified?

Type tests do not expire, but gaskets do. Silicone gaskets typically hold their compression for 8–10 years; EPDM less in chlorinated or oily air. On a refurbishment after ten years, assume the IP is degraded and replace the seals, or plan to replace the fittings.

Next step

If the project has bathrooms, spas or pool decks, the fixtures are where IP, SELV and finish all have to agree at once. Our bathroom and wet-area lighting range lists IP44 to IP68 fittings with the zone each one is intended for, and the gasket and cable-entry details that the datasheet usually omits. Send room types, ceiling heights and the cleaning regime through the project enquiry desk and you will get a fixture schedule with the IP column already filled in.

For the full rating-by-rating matrix, the companion piece is the IP rating chart. If the choice in front of you is specifically IP44 against IP65, that comparison covers where each one fails. Bathroom zone boundaries are set out separately in bathroom lighting zones and IP requirements. Impact resistance (IK) and coastal durability follow different standards and are treated in their own guides.

Christina

Hello, I’m Christina, founder of Qilux Lighting.Qilux Lighting is a China-based decorative and commercial lighting partner, working with distributors, lighting designers, system integrators, and project contractors worldwide.We support commercial and hospitality projects by translating design concepts into reliable, manufacturable lighting solutions, bridging design, production, and delivery.