IP等級が答えるのは、固形物が侵入するか、水がかかったときにどうなるかという2点だけです。IEC 60529は両方の数字を定義しており、ホテル案件の照明器具の仕様書では、ほぼ必ずこれらの数字が記載されています。問題は、保護されているのが前面レンズだけで、背面のケーブル引き込み口が開いたままの器具に、サプライヤーが「IP44」と記載するような場合に生じます。このガイドでは、IP20からIP68までの等級を解説し、ホテル工事の大半に該当する4つの等級を示すとともに、提出書類の承認前に確認すべき事項を列挙します。
1. IPの2つの数字の意味
IPはIngress Protection(侵入保護)の略で、数字は2桁で表記されます。IPに続いて、固形物に関する数字、水に関する数字の順に記されます。IP65があらゆる点でIP44より「優れている」というわけではありません。異なる2つの試験結果を示しているのです。ガスケットが不適切な面に取り付けられていれば、防じん性が高くても散水試験に不合格となる場合があります。

第1数字は0から6までで、固形物に対する保護性能を示します。0では直径50 mmの球体から、6では完全な防じんまでを表します。照明器具にとって重要な基準は5です。IP5Xでは侵入が制限されますが、完全には防止されないため、粉じんが侵入してLED基板に堆積する可能性があります。完全な防じんを示すのは6だけです。繊維状の断熱材が舞う天井裏で使用する器具について、防じん性を主張するなら6に限られます。
第2数字は0から8までで、垂直に落ちる水滴から連続的な水没までを示します。含まれていない項目にも注意してください。結露を示す数字も、塩分を示す数字も、暖かい照明器具から冷たい天井へ移動する水蒸気を示す数字もありません。これらは現場で最もよく見られる3つの故障要因ですが、IP等級はそのいずれについても何も示しません。
| 数字 | 第1数字:固形物 | 第2数字:水 |
|---|---|---|
| 0 | 保護なし | 保護なし |
| 1 | 直径50 mm以上の物体(手) | 垂直に落ちる水滴 |
| 2 | 直径12.5 mm以上(指) | 筐体を15°傾けた状態での水滴 |
| 3 | 直径2.5 mm以上(工具、太い電線) | 垂直から最大60°の範囲からの噴霧 |
| 4 | 直径1.0 mm以上(細い電線、ねじ) | あらゆる方向からの飛まつ |
| 5 | 防じん(完全な防じんではない) | 水噴流(ノズル径6.3 mm) |
| 6 | 完全な防じん | 強力な噴流水、ノズル径12.5 mm |
| 7 | — | 水深1 mで30分間の浸水 |
| 8 | — | 1 mを超える浸水(合意による) |
いずれかの位置に「X」がある場合、その条件で器具が試験されていないことを意味し、合格したという意味ではありません。浴室の鏡照明でIPX4という表示は一般的で、正当なものです。メーカーが水に対する試験のみを実施したことを示しています。防塵性能も必要な場合は、IPX4ではなくIP44と記載してください。
2. IP20からIP68まで:各等級で耐えられる条件
等級の大半はホテルの設備工事には関係ありません。ほとんどの仕様は6つの等級でカバーされます。すべてを暗記するより、各等級がどこまで対応できるかを知るほうが役立ちます。
IP20 乾燥した屋内用器具です。防塵試験も防水試験も行われていません。天井裏を厨房の還気経路として使用せず、天井が乾燥していることを条件に、客室の天井照明、廊下のダウンライト、宴会場のペンダント照明に適しています。 IP23 は鉛直から60°の角度で噴霧を加えた試験に対応します。風雨が軒天の下面には当たるものの、側面には当たらないキャノピーの軒天に適しています。
IP44 浴室や屋根付きテラスで幅広く使われる等級です。直径1 mmの固形物と、あらゆる方向からの水の飛まつに対する保護性能を備え、毎分10 Lの水を5分間噴霧して試験します。IEC 60364-7-701に基づく浴室のゾーン1およびゾーン2での最低要件であり、屋根付きのホテルバルコニーにも適した標準的な選択肢です。
IP54およびIP55 は防塵性能と噴流水への保護を備えています。IP54は防塵形で飛まつに対応し、IP55は防塵形で直径6.3 mmのノズルによる噴流水に対応します。駐車場の軒天、サービス廊下、厨房のバックヤード、機械室などに適した等級です。高圧洗浄機が届く場所では最低でもIP55を指定し、ノズルが1 m以内に近づく場合はIP65を指定してください。
IP65およびIP66 は防塵形で、噴流水に対応します。IP65は、屋外テラス、プール周辺、庭園の小道照明、ファサードのアップライトの標準等級です。IP66は毎分100 Lの水を直径12.5 mmの大型ノズルから噴射する試験に対応しており、洗浄エリアや業務用厨房の壁面で実際に想定される条件に適しています。
IP66はIP65を単に格上げしたマーケティング上の等級ではありません。直径12.5 mmのノズルは、直径6.3 mmのノズルの8倍の流量があり、洗浄壁用に設計された器具と、ゴムリングが付いているだけの器具とを区別する試験です。施設管理担当者が器具の近くで高圧洗浄機を使用する場合は、IP66を指定し、ケーブルグランドも確認してください。実際に水が浸入する箇所はケーブルグランドだからです。
IP67およびIP68 は浸水に関する等級です。IP67は水深1 mで30分間の浸水を意味します。IP68はそれより深い、または長い浸水への対応を意味し、条件は買い手とメーカーの合意によるため、データシートに水深と時間を明記しなければ、等級に意味がありません。プールのニッチ照明、噴水用器具、水景施設のステップライトなどが該当します。ケーブルの引き出し長さが0.5 mで、コネクターが水面より上にあるIP68器具は、コネクターまでしかIP68性能を備えていません。
3. 噴流水と浸水の違い:IPX5、IPX6、IPX7
この3つの等級はそれぞれ異なる試験装置で試験されるため、ある等級に合格しても、ほかの等級への適合についてはほとんど判断できません。これは提出資料の審査で最もよく見られる誤解です。
| 試験 | 方法 | 証明できること | 証明できないこと |
|---|---|---|---|
| IPX4 | 揺動式スプレー、10 L/分、5分間、360° | 水しぶきによる有害な浸水がないこと | 滞留水については何も証明しない |
| IPX5 | ノズル径6.3 mm、12.5 L/分、3分間、距離3 m | 低圧の噴流水に耐えること | 浸水に関する規定なし |
| IPX6 | ノズル径12.5 mm、流量100 L/min、3分間、距離3 m | 強い噴流水(例:洗浄時の水流)に耐える | 浸水に関する規定なし |
| IPX7 | 水深1 m、30分間 | 水深1 mの静水圧下で浸水なし | 噴流水や圧力に関する規定なし |
| IPX8 | 浸水条件(水深・時間)は協議により決定 | データシートに記載された内容 | 記載されていない事項 |
毎分12.5 Lの水流が動圧を伴ってガスケットに当たる一方、浸水では静水圧がかかります。噴流水を遮断できるガスケットでも、一方の端だけが圧縮されている場合、水深1 mでは浮き上がることがあります。反対に、排水経路のないポッティング処理済みのIP67器具は、ケーブルグランドが弱点であれば、噴流水試験後に内部に水が残ることがあります。
ホテルでの実務上の目安は次のとおりです。器具にホースで水をかける場合は、IP65またはIP66を指定し、ケーブルグランドも確認してください。水中に設置する場合は、IP67またはIP68を指定し、ケーブルの長さとコネクターの保護等級を確認してください。「IP65だからプールに設置できる」といった説明を受け入れてはいけません。
4. ホテルでは場所に応じてどの保護等級が必要か
以下の表は、設計段階で私が使用しているものです。意図的に保守的な内容にしています。ダウンライトのIP44とIP65の価格差は小さい一方、3年目に腐食した器具60台を交換する費用は小さくありません。
| 所在地 | 最低IP等級 | 理由 |
|---|---|---|
| 客室、廊下、ロビー(乾燥した天井) | IP20 | 水源なし。ほこりは建設時のもののみ |
| 浴室のゾーン1および2(IEC 60364-7-701に準拠) | IPX4。シャワーヘッドから直接水がかかる可能性がある場合はIPX5 | 水しぶき、および公共トイレでは清掃用ホース |
| 浴室ゾーン0(浴槽またはシャワートレイの内部) | IPX7、SELV 12 V | 浸水および感電の危険 |
| 軒天のある屋根付きテラス、ロッジア、バルコニー | IP44 | 風雨が当たるのは下面のみ |
| 屋根のないテラス、プールデッキ、庭の小道 | 小道用照明はIP65、IK08 | 雨、清掃時の噴射水、時折の衝撃 |
| 業務用厨房、食器洗浄場、ランドリー | IP65、洗浄水がかかる壁面ではIP66 | 蒸気、油脂、高圧洗浄 |
| スパ、スチームルーム、プール施設の天井 | IP65、腐食環境クラスC4 | 塩素を含む蒸気が冷えた金属面で結露 |
| プール水中の照明ニッチ | IP68、使用水深を明記 | 常時浸水 |
| 駐車場の軒天、サービス通路 | IP54~IP55 | ほこり、湿気、時折のホース洗浄 |
| ファサードのアップライト照明、看板照明 | IP65~IP66 | 高所での雨や、風にあおられた水 |
この表では、2つの定格が見落とされがちです。1つ目はプールの天井です。水中ではないため、IP44が指定されますが、塩素を含む蒸気によって、わずか18か月で仕上げが損なわれます。2つ目は公共施設の浴室で、清掃担当者が壁にホースで水をかけるケースです。これは飛沫ではなく噴流水であり、IPX4では耐えられません。
定格の選択に迷う場合は、上位のものを選び、その差額をより優れたガスケットとステンレス製の固定ねじに充ててください。湿気の多い天井では、最初に故障するのはねじです。
5. IPは耐紫外線性、耐塩害性、耐衝撃性を示すものではない
IP等級は、筐体への水や固形物の侵入を表します。筐体が設置環境に耐えられるかどうかは示しません。以下の4つの問題は、すべてIP等級の対象外です。

腐食。 粉体塗装を施したダイカストアルミニウム製の筐体は、IP65であっても、海岸沿いでは2度の夏を経るうちに白亜化、膨れ、孔食が生じることがあります。ISO 9223では腐食性をC1(屋内・乾燥)からC5(海洋環境)、CX(洋上)まで分類しています。海辺のリゾートはC5に該当し、そこで使用する器具には316Lステンレス鋼または船舶用途向けの塗装システムが必要で、ガスケットだけでは不十分です。通常の根拠となるのはISO 9227に準拠した480時間の塩水噴霧試験であり、C5環境では720時間を求めるのが妥当です。
UV. Polycarbonate diffusers yellow and embrittle under UV unless stabilised. A stamped “UV-stabilised PC” claim without a test is worth little; ask for the material grade and the hours of QUV or xenon-arc exposure. Powder coat on a south-facing façade in Dubai or Queensland will chalk unless it is a polyester or PVDF system rated for exterior exposure.
Impact. That is IK, governed by IEC 62262, and it is a separate number. A decorative bollard can be IP65 and IK05, and one knock from a maintenance cart ends it. Path lights and anything at trolley height should be IK08 or better.
Condensation. A sealed IP65 luminaire in a humid space traps moisture that entered during installation. When the light is on the air expands, when it is off the water condenses on the coldest surface — usually the driver or the LED board. This is why good wet-area fittings have a breather valve or a Gore vent, and why “more sealed” is not automatically “more reliable”.
The thermal cost is measurable. Closing the same 15 W downlight from IP20 to IP65 typically raises the driver case temperature by 8–12 K, because the housing that keeps water out also keeps heat in. Electrolytic capacitor life roughly halves for every 10 K rise, so a driver rated 50,000 hours at 60 °C may deliver 25,000 hours at 70 °C. On a hotel with 400 bathroom fittings, that is the difference between a ten-year life and a five-year replacement round.
Finally, read where the rating applies. A front-frame IP44 with an open back plate is an IP44 lens, not an IP44 luminaire. Recessed fittings must be rated for the void they sit in, and a fire-rated downlight in a bathroom ceiling needs its IP declared for the whole body, including the connector block.
6. Testing and certificates to ask for
An IP claim is a type-test result, not a routine production check. Nobody immerses every fixture before shipping. So the evidence you collect at approval stage is the only thing standing between you and a batch that leaks.
Ask for the test report, not the certificate. A certificate of compliance is a one-page statement; the report shows the laboratory, the standard (IEC 60529, or EN 60529 which is identical), the sample configuration and the pass criteria. Check four things in it:
- The report names the exact model and variant you are buying. A family certificate covering twelve sizes is common, and the smallest size often has the thinnest gasket.
- The sample was tested as installed: cable gland fitted, driver in place, diffuser on. Reports tested with a blanking plate are not evidence for the delivered product.
- The second digit was actually tested. IPX4 and “suitable for bathrooms” are not the same statement.
- The date and the laboratory are identifiable, and the lab is accredited for IEC 60529.
Then ask the factory two process questions. Is the gasket compression set by torque or by hand, and is the torque written on the work instruction? Is every unit given a short IP check on the gasket seat, or only a visual? A supplier who can answer both is controlling the variable that actually causes failures.
For projects in the EU and UK, IP sits alongside CE or UKCA marking, RoHS 2011/65/EU and the energy label under EU 2019/2020, all of which are set out in our compliance and sustainability notes. An IP report does not substitute for any of them, and a CE declaration that lists IP65 for a fitting whose report says IP44 is a documentation error worth escalating.
よくあるご質問
Is a higher IP rating always better?
No. A fully sealed IP65 fitting in a dry ceiling costs more, runs hotter and can trap moisture that a ventilated IP20 body would release. Higher ratings also tend to mean bonded lenses that are harder to service. Specify the rating the location needs, plus one step of margin where cleaning practice is uncertain.
Can I use an IP65 light in a bathroom zone 1?
Yes, IP65 exceeds the IPX4 minimum for zone 1, provided the fitting is also suitable for the zone’s shock protection requirements. In zone 1 that usually means SELV at 12 V or a 30 mA RCD-protected circuit, and the fitting must be rated for the ambient temperature of a steamy room.
Does IP44 mean the fitting can go outdoors?
Only under cover. IP44 is splash rated, so a soffit or a balcony with a roof above is fine. Direct rain at an angle, wind-driven spray and standing water are outside its test, and so is UV. For an exposed position, IP65 plus a corrosion class appropriate to the site is the starting point.
What does the X in IPX4 mean?
It means the solid-particle digit was not tested, not that the fitting failed. Many bathroom fittings are legitimately sold as IPX4 because only water ingress matters there. If dust is also a concern, for example in a ceiling void with loose insulation, specify IP44 or IP54 instead.
How often should IP ratings be re-verified?
Type tests do not expire, but gaskets do. Silicone gaskets typically hold their compression for 8–10 years; EPDM less in chlorinated or oily air. On a refurbishment after ten years, assume the IP is degraded and replace the seals, or plan to replace the fittings.
次のステップ
If the project has bathrooms, spas or pool decks, the fixtures are where IP, SELV and finish all have to agree at once. Our bathroom and wet-area lighting range lists IP44 to IP68 fittings with the zone each one is intended for, and the gasket and cable-entry details that the datasheet usually omits. Send room types, ceiling heights and the cleaning regime through the project enquiry desk and you will get a fixture schedule with the IP column already filled in.
For the full rating-by-rating matrix, the companion piece is the IP rating chart. If the choice in front of you is specifically IP44 against IP65, that comparison covers where each one fails. Bathroom zone boundaries are set out separately in bathroom lighting zones and IP requirements. Impact resistance (IK) and coastal durability follow different standards and are treated in their own guides.







