Qilux Lighting

Light Quality Explained: CRI, CCT, TM-30 and SDCM

Işık Kalitesi Açıklaması: CRI, CCT, TM-30 ve SDCM

Bir aydınlatma düzeninin tasarlandığı gibi mi yoksa taviz verilerek mi görüneceğini dört değer belirler: CRI, TM-30 Rf ve Rg, CCT ve SDCM. Bu değerler birbirinden farklı dört soruyu yanıtlar; yalnızca birini belirten bir şartname, tedarikçiye diğer üçünde başarısız olma serbestisi tanır. Bu kılavuz, her bir değerin neyi ölçtüğünü, hangi durumlarda yanıltıcı olduğunu ve otel, restoran ve perakende projelerinde hangi değerlerin güvenilir sonuç verdiğini açıklar. Sahadaki CRI aydınlatma tartışmalarının çoğu, aslında hiç tasarlanmadığı bir görevi yerine getirmesi beklenen bir ölçüt hakkındadır.

1. Işık kalitesini tanımlayan dört değer

Bir ışık kaynağı bir spektrum yayar. Göz, bu spektrumu üç izlenime dönüştürür: renklerin ne kadar doğru göründüğü, beyaz ışığın ne kadar sıcak ya da soğuk göründüğü ve aynı türdeki iki armatürün birbiriyle uyumlu görünüp görünmediği. Dört değer bu izlenimlerle ilişkilidir ve hiçbiri diğerinin yerine geçmez.

Overview of CRI, CCT, TM-30 and SDCM and the different light quality questions each metric addresses
ÖlçütYanıtladığı soruProjelerde yaygın değerGözden kaçırdığı noktalar
CRI (Ra)Sekiz pastel renk örneğinde ortalama renk doğruluğuMisafir alanlarında Ra ≥ 90, servis alanlarında ≥ 80Doygun kırmızılar ve maviler; özellikle R9
TM-30 (Rf, Rg)99 renk örneğinde doğruluk ve gam yönüRf ≥ 90, Rg 97–103Daha az tedarikçi tarafından yayımlanır; yasal bir asgari değer yoktur
CCTBeyaz ışığın sıcak-soğuk ekseninde nerede konumlandığıMisafir odaları için 2700 K, ortak alanlar için 3000 KRenk doğruluğu veya tutarlılığı hakkında hiçbir şey söylemez
SDCMBir armatürün nominal CCT noktasından ne kadar saptığı≤ 3 adım, ideal olarak ≤ 2 adımOptikler, kısma davranışı, yaşlanma

Tablodaki her satır farklı bir şekilde yetersiz kalır. Bir armatür Ra 92 değerine ulaşsa bile az pişmiş bir bifteği gri gösterebilir; çünkü Ra’nın arkasındaki sekiz numunede doygun kırmızı yoktur. Armatür tam olarak 3000 K değerinde olabilir, ancak yanına takılan armatürden yine de dört adım sapabilir. Her iki ölçütte de eşleşebilir, ancak reflektörü yanlış olduğu için duvarda görünür bir halka oluşturabilir.

Tabloda yer almasalar da konuşulması gereken iki değişken daha vardır. İlki, fosfor dönüştürmeli LED’lerde sıklıkla düşüş görülen 480 nm civarındaki spektrum sürekliliğidir; bu düşüş, donuk turkuaz ve çamurlu zeytin tonları olarak kendini gösterir. İkincisi kısma davranışıdır; çünkü çıkış %5’e indiğinde renk sıcaklığını değiştiren veya titremeye başlayan bir sürücü, iyi bir spektrumun sağlayacağı faydayı ortadan kaldırır.

Bunu yanlış yapmak, maliyetin sonradan ortaya çıkmasına yol açar. Teslimden sonra 200 misafir odasındaki gömme spotları yeniden lambalamak; yeni armatürler, işçilik, erişim ekipmanı ve çalışma sırasında envanter dışı kalacak odalar demektir. İkinci partinin ışığı daha yeşil göründüğü için 40 m koridor tavan pervazını değiştirmek daha da kötüdür; çünkü tavanın açılması gerekir. Rakamlar şartname belgesinde birkaç satıra mal olur; başarısızlığın bedeli ise bir değişiklik emridir.

Pratik sonuç basittir. Her SKU için dört rakamın da aynı test raporundan alınmış şekilde tek bir sayfada sunulmasını isteyin ve bunlardan yalnızca birini sağlayabilen tedarikçiyi, diğer üçünü ölçmemiş bir tedarikçi olarak değerlendirin.

2. CRI: Ra neyi ölçer, neyi gözden kaçırır

CRI, CIE tarafından 1965’te yayımlanmış ve 1995’te CIE 13.3 olarak revize edilmiştir. Bir test kaynağını, aynı renk sıcaklığındaki bir referans kaynakla karşılaştırır: 5000 K’nin altında kara cisim radyatörü, üzerinde ise gün ışığı kullanılır. Karşılaştırma, R1’den R8’e kadar Munsell sistemine dayalı sekiz renk numunesiyle yapılır. Bu numunelerin renkleri soluktur: toz pembe, hardal sarısı, zeytin yeşili, açık mavi. Doygun kırmızı yoktur, koyu mavi yoktur, cilt tonu yoktur.

Ra, sekiz bireysel puanın aritmetik ortalamasıdır ve kusursuz eşleşmeye 100 puan verilecek şekilde ölçeklenir. Sorun da bu ortalama alma işleminde başlar. Bir lamba R1–R8’de 95, doygun kırmızı numunesi olan R9’da ise 8 puan alıp yine de Ra 92 olarak raporlanabilir. Bir otel projesinde bu lamba ahşap kaplamanın rengini soldurur, domates bazlı yemekleri kahverengi gösterir ve yakından incelendiğinde koyu tenlerde gri bir ton oluşturur.

RaTipik R9 değeriKabul edilebilir olduğu alanlarYetersiz kaldığı alanlar
800–15Koridorlar, teknik odalar, otoparklar, çamaşırhaneMisafir odaları, restoranlar, perakende teşhir alanları
9025–50Genel misafir odası ve ortak alan aydınlatmasıVurgu duvarları, yiyecekler, üst segment perakende
9550–90Restoranlar, barlar, perakende, sanat eserleri, lavabo önüArka alanlarda genellikle gerekli değildir

Ra, ölçeğin üst ucunda da çözünürlüğünü kaybeder. Aradaki fark Ra 95 ile Ra 98 arasında görsel açıdan küçüktür; R9 20 ile R9 60 arasındaki fark ise yakından bakıldığında kırmızı renkli her yüzeyde belirgindir. Bu nedenle konaklama sektöründeki şartname hazırlayanlar, tek bir CRI değerini kabul etmek yerine Ra ve R9'u giderek daha sık ayrı gereklilikler olarak belirtmektedir.

Ölçüm yöntemi, sayı kadar önemlidir. CRI değeri, armatür kararlı duruma geldikten sonra — genellikle 25 °C ortam sıcaklığında 30 dakika bekletilerek — entegre küre içindeki bir spektro-radyometreyle ölçülür. Optik ve difüzör takılmadan önce, tezgâh üzerindeki çıplak bir LED kartından alınan rapor, duvara ulaşan ışığı tanımlamaz. Optikler kısa dalga boylarını soğurur, difüzörler rengi değiştirir ve her ikisi de nihai spektrumu etkiler.

Bir sınırlama daha: CRI yalnızca kara cisim veya gün ışığı eğrisine yakın kaynaklar için tanımlanmıştır. Yoğun renkli ya da dar bantlı kaynaklar yüksek puan alabilir, ancak yanlış görünebilir. TM-30, bu açığı kapatmak üzere geliştirilmiştir ve daha ayrıntılı olarak şu başlıkta ele alınmaktadır: CRI gerçekte neyi ölçer?.

3. TM-30: Rf, Rg ve renk vektörü grafiği

IES TM-30 was published in 2015 and revised as TM-30-20. It replaces eight samples with 99 colour evaluation samples drawn from real objects — textiles, skin, foliage, paint, food — and it reports two headline numbers instead of one.

Rf is fidelity, 0 to 100, averaged across all 99 samples. It works like Ra but without the pastel bias. Rg is gamut: the area of colour space the source renders compared with the reference. Rg 100 means the gamut matches; above 105 means colours are pushed and look more saturated than life; below 95 means they look washed out.

The third output is the colour vector graphic, a 16-bin map of hue shifts. Each bin, reported as Rcs, shows whether that hue family is pushed or muted. A good 3000 K source for a restaurant typically shows a slightly expanded red bin (Rcs above 100) and near-neutral bins elsewhere. A source with a cyan dip shows the opposite: a collapsed bin around 490 nm, which is what makes white linen look dingy.

ReadingWhat it tells youTypical cause
Rf 92, Rg 100Accurate, neutral, safe defaultBroadband phosphor mix with adequate red
Rf 88, Rg 105Slightly saturated, flattering on food and woodRed-enhanced phosphor
Rf 95, Rg 93Accurate but muted; safe on skin, dull on textilesHigh-fidelity package with low red output
Rf 78, Rg 110Visibly over-saturated, unusable in guestroomsCheap narrow-band red boost

Read Rf and Rg together, never separately. A high Rf with an Rg far from 100 is still a colour cast, just a smooth one. The vector graphic tells you which direction the cast runs, which is the part that matters when the client says the room looks “off” but cannot say how.

The vector graphic also settles arguments that Rf cannot. If a client says the blue-grey carpet reads purple, look at the bin around 470 nm; a positive shift there explains it, and no amount of Rf will. If white shirts look yellow in photographs, the 570–580 nm bins are the place to look. Photographers and retail visual merchandisers care about those two regions more than they care about the headline number.

Watch two things in TM-30 data. First, Rf is measured against a reference of the same CCT, so an Rf 90 at 2700 K and an Rf 90 at 4000 K describe different spectra — do not read them as interchangeable quality. Second, some suppliers publish Rf from a 3000 K test unit and ship 2700 K product; the bin matters. Ask for the report at the CCT you are buying.

Compare the two systems side by side in CRI versus TM-30, including how to read a full report page.

4. CCT and the warm-white range for hospitality

Correlated colour temperature describes where a white source sits on the warm-to-cool axis, measured in kelvin. It says nothing about how well colours render. A 2700 K lamp and a 4000 K lamp can both be Ra 90, and they will still make the same oak floor look like two different materials.

CCTCharacterWhere it belongsMaintained illuminance
2700 KWarm, close to incandescentGuestrooms, restaurants, bars, lobbies after dark100 lx general, 300 lx bedside
3000 KWarm white, close to halogenBathrooms, corridors, retail general300 lx bathroom, 100 lx corridor
3500 KNeutral warmMeeting rooms, open office, spa treatment500 lx meeting, 500 lx office
4000 KNeutralKitchens, laundry, back of house, car parks500 lx kitchen work plane

The hospitality band is narrow by design: 2700 K to 3000 K across guest-facing areas, with a tolerance of no more than 300 K between fixtures inside one view. Go wider and the eye reads the difference as dirt rather than as warmth — one wall looks yellowed, the next looks cold, and no amount of cleaning fixes it.

Colour temperature also moves when the fixture dims, and not all drivers behave the same way. A constant-current driver holds the CCT and simply reduces output; a dim-to-warm driver deliberately shifts the spectrum toward amber; a poor driver drifts by accident, typically 200–400 K downward by the time it reaches 5% output. On a scheme that mixes all three behaviours, the room turns patchy after dark, which is when guests are most likely to notice.

There is a real cost to going warm. Dropping from 3000 K to 2700 K costs roughly 5% of perceived brightness at the same lumen output, so a 2700 K scheme needs 5–10% more delivered lux to feel equally bright. Budget for it in the load calculation rather than discovering it at commissioning. The full comparison is in 2700 K versus 3000 K.

5. SDCM: why 3-step and 5-step look different

SDCM stands for standard deviation of colour matching. It counts how many MacAdam ellipses a fixture’s actual colour point sits away from its nominal CCT. One ellipse is roughly the threshold at which a trained observer notices a difference in a side-by-side comparison, so a 3-step bin covers an area three ellipses wide.

In CIE 1976 u′v′ terms, a 3-step bin at 3000 K spans roughly 0.004 in chromaticity distance, and a 5-step bin roughly 0.007. Those numbers are small on paper. On a 12 m corridor ceiling with 40 downlights in a row, they are the difference between a clean line of light and a run of panels where two near the middle clearly read greener.

BinningApproximate Δu′v′ spanWhere it is enoughRisk
2-step≈ 0.003Feature walls, art lighting, retail displayCost and lead time; limited stock
3-step≈ 0.004Guestrooms, corridors, restaurantsBatch drift if not tracked
5-step≈ 0.007Back of house, plant rooms, car parksVisible mismatch in continuous runs
7-step≈ 0.010Single fixtures in isolation onlyUnacceptable in any repeated array

The datasheet number is only half the story. A 3-step fixture sourced from one bin in January and another bin in June will still mismatch across a phased refurbishment, which is why batch codes matter more than the bin claim. That subject has its own treatment in SDCM and colour consistency.

Colour binning sits alongside flux and voltage binning, and the three interact. A 3-step colour bin split across two flux bins will produce a visible brightness step in a run of downlights even though every unit is within tolerance on colour. Suppliers who only quote a colour bin are quoting a third of the picture; ask for the full bin code, which normally reads as colour, flux and forward voltage in one string.

Ageing shifts colour as well. Phosphor and silicone degrade at different rates, and a fixture that starts at 3-step can drift to 5-step equivalent after 10,000 hours if the thermal design is weak. LM-80 data with TM-21 extrapolation gives a projection; a 25 °C test on a fixture that runs at 60 °C in a ceiling void does not. On a ten-year hotel cycle, that drift is the difference between one refurbishment and two.

Five-step is not automatically wrong. In a plant room nobody will notice. The mistake is accepting 5-step in a guest corridor because it was in stock, then discovering the problem after 200 fixtures are on site.

6. How to write light quality into a specification

A specification that survives procurement is a table with four columns and a verification clause. Write it once per area type, not once per project, and reuse it.

Lighting specification template with fields for color temperature, rendition, consistency and test conditions
AreaCRI / R9CCT and SDCMVerification
GuestroomRa ≥ 90, R9 ≥ 502700 K, ≤ 3-stepLM-79 report per SKU, sample approval
BanyoRa ≥ 90, R9 ≥ 503000 K, ≤ 3-stepLM-79 plus IP rating certificate
Restaurant / barRa ≥ 92, R9 ≥ 602700 K, ≤ 2-stepLM-79, TM-30 report, on-site mock-up
Perakende teşhir alanıRa ≥ 95, R9 ≥ 703000 K, ≤ 2-stepTM-30 with vector graphic
Back of houseRa ≥ 804000 K, ≤ 5-stepLM-79 report

Then add the clause that makes the table enforceable: reports must come from a laboratory accredited to ISO/IEC 17025, must be less than 24 months old, must state the exact driver and optic combination supplied, and must carry the batch code engraved or labelled on the fixture. A report for a bare LED board is not a report for a luminaire.

Add a mock-up clause for anything guest-facing. One bay of ceiling, the actual finish samples, the actual dimmer, viewed at 2700 K and at 10% output. Two hours in a mock-up room resolves more arguments than a week of datasheet exchange, and it is the only reliable way to judge whether R9 50 is enough for the timber veneer on that particular job.

Finally, test what arrives. Pull one fixture in twenty, measure at 100%, 50% and 1% output, and compare against the submitted report. Check for flicker at the bottom of the dimming range, where most drivers misbehave, and check colour shift between two units from different cartons. On a 200-fixture hotel job that is ten measurements and half a day.

For the wider package of hotel lighting design, from fixture selection to commissioning support, see hospitality lighting solutions.

Frequently asked questions

Is CRI 90 good enough for a hotel guestroom?

Yes, provided R9 is specified separately at 50 or above and the CCT tolerance is held to 3-step. Ra 90 with R9 below 20 will make timber and dark textiles look flat. Ra 90 with R9 at 50 reads as accurate in a room at 100–300 lx.

Can a fixture have high CRI and still look wrong?

Regularly. Ra averages eight pastel samples, so a strong red deficiency barely moves the score. A lamp at Ra 92 with R9 at 8 will render food and skin poorly. TM-30 Rf and Rg catch that failure; Ra alone does not.

Do I need both CRI and TM-30 in a specification?

For guest-facing areas, yes. Keep Ra and R9 as the enforceable minimum, since every supplier tests them, and add TM-30 Rf ≥ 90 with Rg between 97 and 103 as the quality gate. Requiring both costs nothing at tender and closes the gap either metric leaves open.

What does a 3-step SDCM mean in practice?

It means every fixture sits within three MacAdam ellipses of the nominal colour point, roughly 0.004 in CIE 1976 u′v′. In a room, adjacent fixtures are then indistinguishable to an untrained eye. 5-step is visibly looser in continuous runs.

Next step

Send the room schedule, ceiling heights and the areas where colour accuracy matters, and the team will return LM-79 and TM-30 reports for the proposed fixtures, plus a sample submission for the finishes you are actually using. Test data for a specific project starts at the capabilities page.

Christina

Hello, I’m Christina, founder of Qilux Lighting.Qilux Lighting is a China-based decorative and commercial lighting partner, working with distributors, lighting designers, system integrators, and project contractors worldwide.We support commercial and hospitality projects by translating design concepts into reliable, manufacturable lighting solutions, bridging design, production, and delivery.