큐럭스 라이팅

Lighting Optics Explained: Beam Angle, Lux and Glare

조명 광학 이해하기: 빔 각도, 럭스 및 눈부심

빔각은 가시광의 가장자리에서 측정하는 것이 아니라, 광도가 최대값의 50%로 떨어지는 지점에서 측정합니다. 이 기준만으로도 36° 다운라이트 두 개가 바닥에 서로 1m나 다른 직경의 빛을 비출 수 있는 이유를 설명할 수 있습니다. 광학 설계는 바닥에 맺히는 빛의 크기, 그 영역 안의 조도(lux), 그리고 앉은 위치에서 광원이 얼마나 밝게 보이는지를 한꺼번에 결정합니다.

각도를 적절히 선택하면 12W 조명이 20W 조명만큼의 효과를 냅니다. 잘못 선택하면 와트 수를 높여 보완하게 되고, 눈부심이 커집니다. 이 페이지에서는 용어, 계산법, 적용 시 고려 사항과 눈부심 한계를 다루므로 샘플이 도착하기 전에 조명 계획을 검토할 수 있습니다.

1. 빔각과 필드각

제조업체는 광도가 최대값의 50%로 떨어지는 지점. 에서의 빔각을 표기합니다. 필드각은 최대값의 10%가 되는 지점. 에서 측정합니다. 두 수치는 동일한 광도 분포에서 산출되며, 곡선상의 서로 다른 높이를 기준으로 같은 원뿔형 배광을 설명합니다.

Conceptual beam angle and field angle diagram showing relative intensity boundaries

실용적인 비율은 약 2:1입니다. 빔각이 36°로 표기된 조명기구의 필드각은 대개 60°~70°입니다. 빔각은 어떤 대상에 조명을 비출 때 활용할 수 있는 빛의 범위입니다. 필드각은 그 범위를 넘어 퍼지는 빛까지 포함합니다.

빔각이 같은 두 조명기구도 실제 조명 효과는 다를 수 있습니다. 차단이 뚜렷한 반사경은 빛 에너지 대부분을 50% 원뿔 안에 모읍니다. 반면 빛이 부드럽고 점진적으로 감소하는 반사경은 광속의 35%를 그 범위 밖으로 내보냅니다. 전자는 테이블 위에 선명한 빛의 원을 만들고, 후자는 주변 천장과 벽까지 비춥니다. 로비에서는 바람직할 수 있지만, 테이블이 각각 분리되어 보이도록 해야 하는 레스토랑에서는 원치 않을 수 있습니다.

샘플을 요청할 때 두 수치를 모두 확인하세요. 빔각만 기재된 데이터시트는 조명기구의 특성을 절반만 설명하는 셈입니다.

고니오포토미터 없이도 어두운 방에서 각도를 측정할 수 있습니다. 조명기구 바로 아래 바닥에 조도계를 놓고 측정값을 기록한 다음, 측정값이 절반이 될 때까지 조도계를 바깥쪽으로 옮깁니다. 그 거리와 설치 높이의 비율은 tan(θ/2)에 해당합니다. 따라서 천장 높이가 2.7m일 때 0.62m 지점에서 측정값이 절반으로 줄어든다면 각도는 24°입니다. 샘플에서 두 번 측정하면 데이터시트와 실제 광학 부품 간의 차이를 확인할 수 있습니다. 이는 모형 조명 테스트의 결과가 예상과 다른 가장 흔한 원인입니다.

빔각배수높이 2.7m에서의 빛 원 직경높이 3m에서의 빛 원 직경높이 4m에서의 빛 원 직경
15°0.2630.71m0.79m1.05m
24°0.4251.15 m1.28 m1.70 m
36°0.6501.75 m1.95 m2.60 m
60°1.1553.12 m3.46 m4.62 m

직경은 다음 공식을 따릅니다 D ≈ 2 × H × tan(θ/2), 여기서 H는 렌즈에서 표면까지의 거리이고 θ는 빔 각도입니다. 배율 열에는 각도를 계산에 반영한 공식이 적용되어 있어, 현장에서 계산기 없이 표를 사용할 수 있습니다. 이 수치는 직경의 50% 지점으로, 3 m 높이의 36° 다운라이트가 직경 1.95 m의 원을 비추면서도 3 m 너머까지 빛이 눈에 보이는 이유입니다.

2. 칸델라, 럭스 및 역제곱 법칙

세 가지 단위로 모든 것을 설명할 수 있습니다. 칸델라(cd) 는 특정 방향의 광도, 즉 조명기구가 그 방향으로 얼마나 강하게 빛을 내보내는지를 나타냅니다. 루멘(lm) 은 조명기구에서 나오는 총 광속입니다. 럭스(lx) 는 1제곱미터에 입사하는 광속이므로 1 lx = 1 lm/m²입니다.

현장에서 중요한 변환식은 E = I / d²: 조도는 광도를 거리의 제곱으로 나눈 값입니다. 설치 높이를 두 배로 높이면 조도는 4분의 1이 됩니다. 이는 기하학적 특성이지 품질 문제가 아니며, 드라이버 설정을 바꿔도 달라지지 않습니다.

24° 배광각의 1,500 lm 다운라이트는 빛을 좁은 원뿔 형태로 집중시킵니다. 최대 광도는 약 12,500 cd이므로, 3 m 지점에서 축상 조도는 대략 12,500 / 9 = 1,390 lx. 동일한 1,500 lm을 60°로 확산하면 광도는 약 1,090 cd이며, 같은 높이에서 조도는 약 120 lx입니다. 소비전력과 광속은 같지만 결과는 11배 차이가 납니다.

이 때문에 루멘만으로 비교하면 문제가 생깁니다. 2,000 lm, 60° 다운라이트와 1,200 lm, 24° 액센트 조명은 서로 경쟁하는 제품이 아니라 각각 다른 용도에 맞는 제품입니다. 조명 기구 일람표에 소비전력과 루멘만 있고 배광각이 없다면, 시공할 천장 높이에서의 조도를 계산할 수 없습니다.

역제곱 법칙은 표면에 수직으로 측정한 축상에서만 성립합니다. 축을 벗어나면 입사각의 코사인만큼 조도가 더 낮아집니다. 연직 하향 방향에서 45° 벗어난 지점에서는 광원의 자체 배광에 따른 감쇠를 고려하기 전에도 표면 조도가 축상 값의 71%에 불과합니다. 따라서 빛이 비추는 영역의 가장자리에서는 거리만으로 예상하는 것보다 조도가 더 빠르게 낮아집니다.

조명 기구최대 광도2.7m3m4m6m
1,500lm, 24°≈ 12,500cd1,715lx1,390 lx780lx347lx
1,500lm, 36°≈ 5,600cd768lx622lx350lx156lx
800lm, 60°≈ 1,090cd150lx121lx68lx30 lx

여기서 최대 광도는 빔 입체각 전체의 평균값의 1.15배로 추정됩니다. 실제 값은 배광 파일에서 확인할 수 있으며, 이 추정치는 루멘만 표시된 데이터시트를 대략적으로 검증하기 위한 참고값일 뿐입니다.

3. 용도에 따른 빔 각도 선택

천장 높이는 설치 가능 범위를 정하고, 작업 대상의 배치는 각도를 결정합니다. 조명할 표면에서 등기구 방향으로 거슬러 올라가며 계획해야 하며, 그 반대 순서로 해서는 안 됩니다. 높이 4.5m인 로비에 24° 등기구를 설치할 경우, 빛이 서로 떨어져 어두운 구역이 생기지 않도록 등기구 간격을 약 1.7m로 해야 합니다. 같은 등기구를 15°로 설치하면 빛이 닿지 않는 어두운 띠가 생깁니다.

  • 15°–20°: 예술품, 식물, 탁자 중앙 등 단일 물체를 강조하는 조명. 높이 4m에서 스폿 직경은 1.1m 미만이므로, 등기구 간격보다 조준 방향이 더 중요합니다.
  • 24°: 매장 디스플레이, 리셉션 데스크, 높은 벽면의 월워싱에 적합한 기본 각도입니다. 대비를 만들기에 충분히 좁으면서도 약간의 조준 오차를 감안할 만큼 넓습니다.
  • 36°: 객실, 레스토랑, 라운지의 일반 다운라이트 조명에 적합합니다. 높이 3m에서 1.95m를 비추므로, 1.8~2.2m 간격으로 배치된 테이블에 잘 맞습니다.
  • 60°: 통로, 욕실, 백오브하우스 공간에 적합합니다. 넓은 빛 범위를 제공하고 광축상의 조도는 낮으며, 균일한 조명에 필요한 등기구 수가 적습니다.
  • 비대칭형: 빔이 10° × 60°로 아래쪽이 아닌 측면으로 퍼지는 선형 월워셔 및 선반 조명에 적합합니다.

용도보다 설치 높이가 결과에 더 큰 영향을 미칩니다. 높이 2.7m에 설치한 36° 등기구는 편안한 일반 조명을 제공하지만, 6m 높이에서는 은은한 빛만 제공하므로 보조 조명 없이는 로비 바닥의 200 lx를 충족할 수 없습니다. 높이가 4m를 넘으면 각도를 좁히고 와트를 높이거나, 주변 조명을 두 번째 조명 레이어로 보완해야 합니다.

공간일반적인 각도설치 높이조명 대상 표면의 결과
호텔 로비, 강조 조명15°–24°4~6m0.8~2.6m 빛 범위, 광축상 500~1,400 lx
객실 일반 조명36°–60°2.6~2.8m1.6~3.2m 빛 범위, 100~200 lx
레스토랑 테이블24°–36°2.4–3 m1.0–2.0 m 조명 영역, 테이블이 독립된 구역으로 인식됨
소매 매장 디스플레이15°–24°2.8–3.5 m750–1,000 lx, 주변 조도의 3배
복도60°2.4–2.7 m2.8–3.1 m 조명 영역, 균일한 100 lx
사무 작업60°–90°2.7–3 m조명 영역이 겹치며, 유지 조도 500 lx

4. Glare: UGR, luminance and shielding

Glare is not brightness. It is brightness relative to what surrounds it. A 3,000 cd/m² downlight against a 200 cd/m² ceiling is uncomfortable; the same fixture against a bright window is invisible. That ratio, plus the angle between the source and the viewer’s line of sight, is what UGR models.

Sightline comparison of an exposed light source and a shielded luminaire in a seating area

Unified Glare Rating runs on a 10–28 scale. EN 12464-1 sets UGR ≤ 19 for offices and writing tasks, ≤ 22 for dining, and ≤ 25 for corridors and back-of-house. Reading in bed is stricter still; treat UGR ≤ 16 as the target when the source can enter a guest’s field of view at 1 m.

Shielding does most of the work. A shielding angle of 30° or more — the angle between the horizontal and the line from the lamp to the baffle edge — keeps the LED out of sight for anyone standing or seated below. A baffle 40 mm deep typically buys 3–5 UGR points at the same output. A honeycomb or cross-louvre accessory buys another 2–3, at the cost of 8–12% of the lumens.

The other variable is where the eye sits. UGR weights each source by a position index that rises steeply as the source moves toward the centre of the field of view. A 1,000 cd/m² fitting 45° above the sightline contributes far less than the same fitting 10° above it, which is why recessing or a snoot beats a lower-output lamp in a guestroom.

The counter-intuitive part: narrow beams glare more. A 15° accent at 500 cd has a small bright source, and small bright sources are exactly what the eye reacts to. That is why accent fittings in guestrooms need deep recessing or a snoot even though their total output is modest. Full treatment of the calculation, luminance limits and placement errors is in the UGR and glare guide.

Luminance is the number to check, not lux. Above roughly 1,000 cd/m² at normal viewing angles, a source in the field of view starts to read as a point of discomfort in a dim room. That threshold is why the same fitting works in a 300 lx office and fails in a 50 lx lounge.

5. Reading IES/LDT photometric files

Two formats cover almost every project: IES LM-63 (.ies) and Eulumdat (.ldt). Both hold a candela table sampled over vertical and horizontal angles, plus the luminaire’s total flux and wattage. Neither is a rendering; both are measurements of one physical sample.

What to check, in order:

  • Total flux in the file matches the lumen figure on the datasheet. A 2,000 lm claim with a 1,780 lm file is common, and the file is the honest one.
  • C-plane count. Rotational symmetry needs at least two planes; an asymmetric wall washer needs 0°/90° or more, or the file cannot describe it.
  • Vertical angle step. A 5° step rounds off a 15° beam badly. 2.5° or finer is normal for narrow optics.
  • Absolute vs relative photometry. Relative files are scaled by a factor; if the software ignores it, every lux value is off by that factor.
  • Spacing criterion, if present, gives the manufacturer’s own mounting-height multiple for even coverage. It is a useful cross-check on the spacing you planned.

DIALux and Relux both read either format, and both will happily calculate a room from a file that does not match the delivered product. The check is administrative, not technical: compare the file’s total flux and wattage with the purchase order, then check the revision date. Facilities teams that keep a copy of the submitted file with the project handover avoid the argument two years later when a replacement is ordered.

Optical efficiency is the share of LED flux that leaves the fitting. It ranges from about 55% in a heavily baffled accent to over 85% in a polished reflector, and it is not visible in a lumen figure taken at the LED. Two fittings with the same chip and different optics can differ by 30% in delivered lumens, which is one more reason to quote the file rather than the LED datasheet.

A file is valid only for the exact LED, bin and driver combination that was tested. Swap the driver for a different output current and the candela table no longer applies. For project submissions, ask for the LM-79 test report alongside the file, and check that the report’s date is after the last LED change. Files older than the current BOM are the most common reason a mock-up does not match the calculation.

Wall washing and grazing need asymmetric distributions that no round-beam table can describe. Those optics are covered separately in wall washing versus wall grazing, including the offsets and spacing that keep a wall even.

6. Optics checklist for specifiers

Run this list against any submitted schedule or sample. Each line catches a failure that shows up on site, not in the render.

  • 빔각 and field angle quoted, both from a current photometric file.
  • Spot diameter calculated at the actual mounting height, not the catalogue’s 1 m reference.
  • Lux on the task surface checked after applying the maintenance factor (0.8 is a fair default for a hotel).
  • Spacing between fittings no more than 1.2× the spot diameter, or pools will separate.
  • UGR ≤ 19 for task areas, ≤ 22 for dining, and shielding angle ≥ 30° wherever the source is visible.
  • Source luminance under 1,000 cd/m² at the angles a guest will actually look from.
  • Beam angle consistent across a run. Mixing 24° and 36° in one ceiling line is visible from the door.
  • Photometric file dated after the last LED or driver change, with the LM-79 report attached.
  • Asymmetric optics specified for wall washing, with the 10° × 60° orientation marked on the drawing.
  • Colour temperature within 300 K across the visible field, so no fixture reads as a different white.

Most of these are cheap to fix on paper and expensive to fix after the ceiling is closed. The arithmetic in sections 1 and 2 takes about ten minutes per room type and settles the arguments before the mock-up.

Frequently asked questions

Is beam angle the same as field angle?

No. Beam angle is where intensity falls to 50% of peak; field angle is where it falls to 10%. The field angle is always wider, typically 1.7 to 2 times the beam angle. Use beam angle for spot size and lux calculations, and field angle to judge spill onto walls and ceilings.

Does a narrower beam angle give more lux?

Yes, at the same lumen output. Narrowing from 60° to 24° concentrates the same flux into about one sixth of the solid angle, so on-axis intensity rises roughly sixfold. That is why a 12 W accent can out-light a 25 W wide-beam downlight directly under it, and why the accent glares more.

What beam angle suits a 3 m hotel corridor?

Use 60° for the general layer at 2.4–2.7 m, giving 2.8–3.1 m pools that overlap into an even 100 lx. If you want scallops on the wall instead, use 24° wall washers at 0.6–1.0 m from the wall with spacing no wider than the offset.

What UGR is acceptable in a guestroom?

EN 12464-1 does not set a guestroom figure. In practice, keep any source in the sightline at UGR ≤ 16 to 19, and keep bedhead reading lights below 1,000 cd/m² at the pillow. A 300 lx reading task with a deep-set 24° fitting works; an exposed 15° spot at the same output does not.

Can I compare lux figures between two brands’ datasheets?

Only if both use the same distance, the same beam angle and the same reference surface. Many datasheets quote lux at 1 m, which flatters narrow optics. Recalculate from candela and your real mounting height before comparing, or the comparison is meaningless.

Next step

If you are checking a schedule against these rules, the fastest route is the photometric file itself. Qilux supplies IES and LDT files, LM-79 reports and lux calculations for the exact LED and driver combination quoted, per room type and mounting height. Send the ceiling heights and the surfaces you need to light through our engineering capabilities page, and the files come back with the beam angles already resolved into spot diameters and maintained lux.

For fixture families by application, start with the downlight range or architectural project lighting. If the task is sizing rather than optics, the beam angle calculator walkthrough takes the same formula and applies it room by room.

크리스티나

안녕하세요. Qilux Lighting의 설립자 크리스티나입니다.Qilux Lighting은 중국에 기반을 둔 장식용 및 상업용 조명 파트너로,, 전 세계의 유통업체, 조명 디자이너, 시스템 통합업체 및 프로젝트 시공업체와 협력합니다. 당사는 상업 시설 및 호텔·숙박 시설 프로젝트를 지원하며, 디자인 콘셉트를 신뢰할 수 있고 제조 가능한 조명 솔루션으로 구현하여, 디자인, 생산 및 납품을 연결합니다..

소셜 미디어에서 팔로우하세요