Chandelier size for dining table work comes down to two numbers: the diameter, and the height of the lowest point above the tabletop. Once the table is fixed, diameter comes from the table, not the room. A 1.6 m table takes 60–80 cm across. A 3.0 m table takes 85–110 cm. Height runs 75–90 cm above the tabletop, and it climbs about 5 cm for every 30 cm of extra ceiling. Get them right and the fixture sits in the room. The tables below run from 4 to 12 seats and give the numbers I would schedule.
1. The standard formula and its limits
Four rules circulate. Two survive contact with a real table.
The room rule. Add the room length and width in metres, multiply by 8, and you have the diameter in centimetres. A 3.6 × 4.2 m dining room gives (3.6 + 4.2) × 8 = 62 cm. This is a ceiling, not a target. Past it the fixture starts to own the room rather than serve the table.
The table rule. Diameter runs 1/2 to 2/3 of the table width. Over a 90 cm wide table that is 45–60 cm. Applied literally, that size lights the centrepiece and leaves both end settings in shadow, because the fittings sit at the centre of a 1.6 m long top. The rule was written for round tables of about 1.2 m diameter, where width and length are the same number.
The linear rule. For a rectangular fixture, the length runs 2/3 of the table length: 107 cm over a 160 cm table, 140 cm over a 210 cm one. This one holds at every size, because a linear body throws a band of light the same shape as the table.
The sum rule. Table length plus width in feet, read as inches. A 210 × 100 cm table is 6.9 × 3.3 ft, so 10.2 inches, or 26 cm. That is a pendant for a bedside table. The sum rule was derived for 12 ft rooms and breaks when it is moved onto an object a quarter of that size.
What actually holds over a rectangular top is 0.7 to 0.9 of the table’s short side, with a 50 cm floor. Over an 80 cm table that is 56–72 cm; over a 120 cm table, 84–108 cm. It keeps the fixture proportional to the seating on both long sides, which is what the eye reads. Four rooms run through both rules:
| Room (m) | Table (cm) | Room check | Short-side band | Specified |
|---|---|---|---|---|
| 3.0 × 3.6 | 120 × 80 | 53 cm | 56–72 cm | 58 cm |
| 3.6 × 4.2 | 160 × 90 | 62 cm | 63–81 cm | 70 cm |
| 4.2 × 5.4 | 210 × 100 | 77 cm | 70–90 cm | 80 cm |
| 5.4 × 6.6 | 300 × 120 | 96 cm | 84–108 cm | 100 cm |
Where the room check lands below the table band, the room is under-sized for the table. Take the lower figure and expect the fixture to dominate; above 4.2 m the two rules agree and the band’s midpoint is safe.
2. Worked sizes from 4 to 12 seats
The table below assumes standard commercial seating at 60–65 cm per cover, 75 cm table height, and a rectangular top. Diameter is for a round or oval body; linear length runs 2/3 of the table length as above. Both columns are what I would accept at sample approval.

| Seats | Typical table (cm) | Round / oval diameter | Linear fixture length |
|---|---|---|---|
| 4 | 120 × 80 | 55–70 cm | 80–90 cm |
| 6 | 160 × 90 | 60–80 cm | 100–110 cm |
| 8 | 210 × 100 | 70–90 cm | 130–140 cm |
| 10 | 260 × 110 | 80–100 cm | 160–175 cm |
| 12 | 300 × 120 | 90–110 cm | 190–200 cm |
A 1.5 m round table seats eight and takes 90–100 cm, because there is no long axis to leave dark. A table pushed against a wall loses one side, so the lower end of the band still reads correct.
A fixture that passes the table rule but crowds a sideboard is the signal to go lower and wider, not narrower.
3. Ceiling height adjustment
Clearance is a band, not a number. At 75 cm under a 3.4 m ceiling the fixture reads as a gap; at 90 cm under a 2.4 m ceiling it reads as a hazard. The table gives the lowest point above the tabletop and the drop left for body, chain and canopy over a 75 cm table.
| Ceiling height | Fixture bottom above tabletop | Total drop available | Typical fixing |
|---|---|---|---|
| 2.4 m | 75 cm | 90 cm | Semi-flush or short stem, no chain |
| 2.4–2.6 m | 75 cm | 90–110 cm | Stem, 1–2 links of chain |
| 2.6–2.8 m | 80 cm | 105–125 cm | Chain with canopy |
| 2.8–3.1 m | 85 cm | 120–150 cm | Chain, longer canopy skirt |
| 3.1–3.6 m | 90 cm | 145–195 cm | Chain plus decorative rod |
| Above 3.6 m | 90 cm, extended | 195 cm + | Rod, or a two-tier body |
The arithmetic is simple enough to do on site: drop = ceiling height − 75 cm table − clearance. A 2.7 m ceiling with 80 cm clearance leaves 115 cm. If the body is 60 cm deep, the chain and canopy take 55 cm. Order that split stated, not a generic 100 cm chain, or the installer cuts it and the canopy no longer covers the cut.
Above 3.6 m the clearance stops rising; what changes is body size, because a 60 cm fixture disappears at that height and needs 80–100 cm. An off-centre beam or ceiling rose moves the fixture off the table axis, which no drop adjustment fixes.
4. Round vs linear fixtures
A round body over a rectangular table is the common choice for four to six seats, where the fixture covers the middle two settings and the ends are lit by the room. It stops working at eight seats: a 210 cm table needs light along 1.4 m, and a single 80 cm drum leaves 35 cm of table at each end outside the pool.

The linear option solves that. A 140 cm linear body at 2.7 m over a 210 cm table gives even coverage across all eight covers, and it reads calmer in a low room because the eye follows the table rather than a sphere. The trade is that a linear fixture needs a longer, straighter ceiling: any beam within 100 mm of the fixing line forces a canopy redesign.
Two or three pendants over a long table is the third route. Space them evenly: with three pendants over 300 cm, centre-to-centre spacing is 75 cm and the outer units sit 37.5 cm in from each end. Keep each pendant at 40–50 cm diameter so the group reads as a set rather than a row of separate objects.
5. Clearance above the table
The band exists for three reasons: you must see the person opposite without ducking, a serving dish must clear the fixture, and the light must land on the plate. Below 75 cm the fixture enters a seated diner’s sightline; above 90 cm it stops reading as connected to the table. At dinner the level also needs to fall to 30–40% without colour shift, which is a dimming protocol question, not a fixture one.
A second clearance matters in restaurants. The bottom sits 150–165 cm above the floor, and anyone standing at the table edge is inside that envelope. That is why 75 cm belongs to domestic dining and banquettes, while a free-standing table with staff on both sides runs at 85–90 cm.
Where the fixture hangs over a walkway as well as a table, the floor clearance rule takes over: 2.1 m clear below the lowest point. A 2.4 m ceiling cannot do both a 75 cm table clearance and 2.1 m over a walkway; the table has to move, or the fixture becomes a semi-flush mount.
6. When to break the rule
Break the diameter rule when the fixture is the room’s one deliberate object. In a double-height space a 1.5 m chandelier over a 2.6 m table is correct: the mass does the work of a ceiling, and the 0.7–0.9 rule would leave a lampshade at 6 m. Break it downward in a small room, where 55 cm over a 120 cm table beats 70 cm crowding the chairs.
Break the clearance rule when seating is fixed and the table is a bar top. A 105 cm counter with stools needs 75–80 cm, not 90 cm, or the fixture is out of the conversation. Break it upward over a buffet or a sideboard used for service, where 90–100 cm keeps trays clear.
Do not break the walkway clearance. The 2.1 m figure is a head injury number, not a design preference.
A table seating 14 or more settles the question: no round body covers a 3.6 m top. The options are a linear body, a pendant row, or two large fixtures at 1/3 and 2/3 of the length. What fails is one 120 cm chandelier in the middle, lighting four covers of fourteen.
Frequently asked questions
How big should a chandelier be over a 6-seat dining table?
For a 160 × 90 cm table, 60–80 cm diameter as a round or oval body, or 100–110 cm as a linear one. The 0.7–0.9 short-side rule gives 63–81 cm, so the band is safe. If the ceiling is above 3 m, take the upper end; a 60 cm fixture reads small at that height.
Is 75 cm or 90 cm the right clearance above a table?
Both, depending on the ceiling. Use 75 cm up to a 2.6 m ceiling, 80 cm at 2.6–2.8 m, 85 cm at 2.8–3.1 m and 90 cm above that. In restaurants with service on both sides of the table, 85–90 cm is the working norm even at 2.6 m.
Can I hang a chandelier over a table with a 2.4 m ceiling?
Yes, but the body has to be shallow. A 2.4 m ceiling with a 75 cm table leaves 90 cm total drop, so the fixture including canopy must be under about 85 cm deep. A semi-flush mount or a 40 cm deep drum works; a 70 cm tiered chandelier with chain does not.
Should the chandelier be wider than the table?
No. Keep the widest point of the body within the table’s short side, and within 0.9 of it for comfortable proportion. A fixture wider than the table blocks the sightline across the setting and makes the table look borrowed from a smaller room.
Sizing a table that is not on any standard list? Send the table dimensions, ceiling height and seat count through the project enquiry desk, and the drawing comes back with diameter, drop split and canopy size marked. Custom chandelier builds start from that drawing. For which fixture type suits a space rather than how big it is, the hotel lobby and guest space guide covers selection.






