Qilux Lighting

EU Ecodesign and UKCA: What Hotel Projects Must Check

EUエコデザイン規則とUKCA:ホテルプロジェクトで確認すべきこと

A luminaire can be perfectly built, beautifully finished and still be illegal to place on the market, because the rules that decide this are about documents rather than light output. Since September 2021 the EU has applied ecodesign limits to light sources, the UK has run its own marking regime in parallel, and both now expect the manufacturer to hold test evidence rather than a certificate bought from a website. This guide sets out what each regulation actually requires, where CE and UKCA differ, which declarations a hotel project should collect, and the specific documents that hold up a handover when they are missing.

1. ERP 2019/2020 in one page

Regulation (EU) 2019/2020 sets ecodesign requirements for light sources and separate control gear. It does not regulate luminaires as such, which is the source of most confusion on a project, because a luminaire is caught indirectly.

The scope works like this. A light source — a lamp, a module, an LED strip — must meet the requirements to be placed on the EU market. A luminaire that contains a light source must contain one that complies, and must allow that source to be replaced without destructive disassembly, unless the manufacturer declares the luminaire as a “containing product” that cannot be opened. A luminaire with an integrated, non-replaceable LED module is assessed as though the module were the light source, and the whole fitting inherits the assessment.

Four requirements matter to a specifier. Minimum efficacy, which rises in stages and rules out most low-output decorative sources. Colour rendering at Ra ≥ 80 for the source to claim compliance. Standby power limits for any product with a standby mode. And flicker metrics, dealt with in section 4.

There are exemptions, and they are narrow: light sources for emergency lighting, for explosive atmospheres, for radiological and nuclear installations, for military and civil-defence use, and for transport vehicles. Decorative “mood” lighting is not exempt, which is why the low-efficacy filament lamps that filled hotel corridors in 2019 have largely gone. If a specification written in 2019 still names one, the product may no longer be placeable, and the substitution will have a different wattage and a different lumen output. Write a substitution clause before tender rather than after.

2. CE marking and the UKCA transition

CE marking on a luminaire is a self-declaration, but “self” means the manufacturer holds the evidence, not that no evidence is needed. For a typical decorative fitting the applicable directives are Low Voltage 2014/35/EU for mains-voltage products, EMC 2014/30/EU, RoHS, and ecodesign where a light source or control gear is supplied.

Market review diagram distinguishing Great Britain, Northern Ireland and European Union marking routes

The technical file behind the mark has to contain the risk assessment, the standards applied, the test reports, the label artwork and the Declaration of Conformity. It must be kept for ten years after the last unit is placed on the market, and it is the file an authority asks for if a fitting is questioned on site.

UKCA is the GB equivalent, introduced in 2021. The position has moved twice since, and the practical summary for a hotel project is: for electrical safety and EMC, GB has continued to recognise CE, with an indefinite extension announced in 2024. For the GB RoHS and ecodesign regimes, CE recognition was not extended in the same way, so a product needs UKCA or the applicable UK conformity route for those aspects. A dual-marked product with both an EU and a GB Declaration of Conformity is the low-risk answer, and it is what a UK main contractor will ask for.

Two practical consequences. First, ask for the GB declaration separately; suppliers often send the EU one and assume it covers both. Second, check the position at the date of the order rather than relying on this page, because the transition has been extended more than once and the exemptions have changed each time.

3. RoHS and REACH for finishes

RoHS 2, Directive 2011/65/EU as amended by (EU) 2015/863, restricts ten substances in electrical equipment: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, polybrominated diphenyl ethers, and four phthalates. Limits are 0.1% by weight in homogeneous material, except cadmium at 0.01%.

“Homogeneous material” is the phrase that decides most arguments. A brass body, a lacquer coating, a solder joint and a crystal drop are four separate materials, and each is assessed on its own. This is why a fitting can pass on the electronics and fail on the finish, and why the finish supplier is part of the compliance chain rather than outside it.

Brass is the usual point of tension. Many free-machining brasses contain 1–3% lead, which is far above the 0.1% limit, and they rely on a RoHS exemption for lead as an alloying element in copper alloys up to 4% by weight. The exemption is legitimate, but it must be claimed by number in the declaration. A supplier who says “our brass is RoHS compliant” without naming the exemption has either used a lead-free alloy or has not checked.

REACH is separate and catches the finishes RoHS misses. Substances of Very High Concern above 0.1% by weight in an article require communication down the supply chain and to consumers on request, and since 2021 an EU article containing an SVHC above that threshold must also be notified to the SCIP database. Lead crystal is the classic case: at PbO ≥ 24% the lead content is orders of magnitude above 0.1%, so a declaration is unavoidable. The candidate list is updated twice a year, so ask for a declaration dated within the last six months rather than one from 2019.

4. Flicker and efficacy limits

Flicker moved from a comfort issue to a legal limit when 2019/2020 took effect, and the test methods in 2021/341 define how it is measured. Two metrics apply to the light source: SVM, the stroboscopic effect visibility measure, at or below 0.4, and Pst LM, short-term flicker severity, at or below 1.0.

These sit alongside the older IEEE 1789-2015 guidance, which is still the reference most lighting designers use for modulation depth: below 90 Hz the depth should stay under 8%, between 90 Hz and 1,250 Hz the limit relaxes linearly, and above 1,250 Hz there is effectively no restriction. A driver that dims by low-frequency PWM will fail the first test and pass nothing else.

パラメーターLimitReferenceWhere it is checked
SVM (stroboscopic effect)≤ 0.4EU 2019/2020Light source, at full and dimmed output
Pst LM (short-term flicker)≤ 1.0EU 2019/2020Light source, 10-minute measurement
Modulation depth below 90 Hz< 8%IEEE 1789-2015Driver output waveform
Colour rendering for complianceRa ≥ 80EU 2019/2020Light source datasheet
Standby power≤ 0.5 WEU 2019/2020Control gear in standby
Networked standby≤ 2 WEU 2019/2020Connected light sources

Flicker gets worse as dimming deepens, so the measurement point matters. A fixture that passes at 100% and fails at 1% will still be installed at 1% in a hotel guestroom at midnight. Ask for the waveform at 100%, 50% and 10%, and treat a datasheet that quotes only full output as untested. Our guide to dimming and switching in hotel lighting covers which protocols produce which behaviour.

On efficacy, the regulation sets a floor and nothing more. A product that just clears the threshold is compliant and still a poor choice for a 150-key hotel, because the operating cost sits with the owner for a decade. Use the legal limit as the entry ticket and the specification as the real requirement — our explanation of lumens and efficacy covers how to set that requirement.

5. Declarations and test reports

The Declaration of Conformity is a short document with a fixed job: identify the manufacturer, identify the product, list the directives and standards applied, name the signatory, and state that the product conforms. It is not a certificate, it is not issued by a third party for most luminaires, and it is worthless on its own.

製品の信頼性を裏付けるのは、その根拠となる一連の試験報告書です。装飾用照明器具の場合、基本となるのはEN IEC 60598-1と、該当する製品群の個別要求事項を定めたPart 2の規格です。さらに、光生物学的安全性に関するEN 62471、エミッションおよびイミュニティに関するEN 55015とEN 61547、高調波に関するEN 61000-3-2、電源装置に関するEN 61347が含まれます。IP等級を表示する場合はIEC 60529が適用され、光源を付属する場合はエコデザイン情報シートが必要です。

不備のある申請の大半は、次の3点を確認すれば見抜けます。第一に、報告書に、供給対象の正確な型式番号が記載されているか。消費電力の高い仕様や異なる電源装置を採用した仕様も含めて確認します。「類似」モデルの報告書しかないことが、最もよくある不備です。第二に、該当する試験について、試験所がISO/IEC 17025の認定を受けているか。第三に、報告書の日付が適合宣言書より前であり、宣言書に記載された規格が、実際に報告書で試験された規格と一致しているか。

プロジェクトでは、さらに4つ目の確認事項があります。適合性関連書類の中で、証明書と製品コードが対応付けられているか、という点です。索引のないPDFの寄せ集めは、適合性関連書類とはいえません。納入する各照明器具と適合宣言書を結び付ける一覧表こそ、工事監理者が実際に使用する書類です。

6. 引き渡し時に収集する書類

引き渡しの時点で、適合性対応はサプライヤーの責任から所有者の責任へと移ります。必要書類は入札時に揃え、納品時に再確認してください。最終週になってから着手するものではありません。

Handover document checklist for luminaire identification, declarations, reports and traceability
  • 製品群ごとの適合宣言書。EU市場と英国市場の両方が対象となる場合は、それぞれの市場向けのもの。
  • 各適合宣言書に記載された規格に対応し、型式番号が納入品と一致する試験報告書。
  • RoHS適合宣言書(適用する場合は、番号を含む適用除外の明記)および、該当する場合はSCIP参照番号を記載した日付入りのREACH SVHC声明書。
  • すべての光源について、エコデザイン製品情報シートとエネルギーラベル。EPREL登録番号も記載します。
  • 調光方式、定格寿命、周囲温度範囲を含む電源装置のデータシート。
  • 市場の言語で作成された設置・保守説明書、および実際に使用するラベルのデザインデータ。

引き渡しが滞る最も一般的な原因は、証明書の欠落ではありません。証明書と天井に設置された照明器具との対応が確認できないことです。たとえば、9 W品を納入したのに12 W仕様の報告書しかない、製造時に電源装置が代替品に変更された、あるいはバリューエンジニアリングの段階でランプが変更されたのに旧製品のエネルギーラベルが使われている、といったケースです。索引があればこの問題を解決できます。発注時に作成しておけば、作業時間は1時間ほどです。索引は購入者とサプライヤー間のメールに埋もれさせず、O&Mマニュアルに保管してください。3年後に必要とする人は、そのメールのやり取りにも購入者にもアクセスできない可能性があるためです。

よくあるご質問

英国では、照明にUKCAマークが今も必要ですか?

電気安全およびEMCについては、英国本土(GB)ではCEマークの受け入れが継続されており、2024年に期限を定めない延長が確認されました。一方、GB RoHSおよびエコデザインについては、CEマークの相互承認が同様には延長されていないため、UKCAマークまたは英国の適合性評価手続きが引き続き適用されます。CEとUKCAの両方を表示し、それぞれの適合宣言書を用意するのが安全な仕様です。

CEマークがあれば、RoHSへの適合も証明されますか?

RoHSはCEマークの根拠となる指令の一つであるため、適合製品ではRoHS適合を宣言します。しかし、マークそのものは適合の証明にはなりません。根拠となるのはRoHS適合宣言書と、それを裏付ける材料試験データです。宣言書を取り寄せ、真鍮部品に特定の適用除外が利用されていないか確認してください。

EPREL番号とは何ですか?

EPRELは、エネルギーラベルに関するEUの製品データベースです。EU市場で販売されるすべての光源は、販売前に登録する必要があります。登録番号によって、製品とそのエネルギーラベルおよび製品情報シートが紐付けられます。サプライヤーが番号を提示できない場合、その製品は登録されていません。

ホテル用照明器具はERP 2019/2020の対象ですか?

照明器具は間接的に対象となります。同規則は光源および独立型制御装置に適用されるため、照明器具には適合する光源を組み込み、破壊的な分解をせずに交換できるようにする必要があります。LEDモジュールが一体化され、交換できない場合は、そのモジュールを光源とみなして照明器具を評価します。

次のステップ

入札書類一式や引き渡し書類として必要な場合は、検討中の照明器具シリーズについて、適合宣言書、試験報告書、製品情報シートをお送りします。製品コードごとに整理しているため、納入品と照合できます。書類一式は コンプライアンスとサステナビリティ, からご請求いただくか、仕様書を プロジェクトお問い合わせ窓口 までお送りください。仕様書の各項目に対応した書類一覧をお返しします。これらの宣言書に記載された仕上げについては、 照明器具の仕上げと素材に関するガイド.

クリスティーナ

こんにちは。Qilux Lightingの創業者、クリスティーナです。.Qilux Lightingは中国を拠点とする、装飾照明および商業照明のパートナーです,以下の方々と連携しています 世界各地の販売代理店、照明デザイナー、システムインテグレーター、プロジェクト施工業者 。私たちは、 商業施設やホスピタリティ施設のプロジェクト を支援し、 デザインコンセプトを、信頼性が高く製造可能な照明ソリューションへと具現化します,そして デザイン、製造、納品をつなぎます.

ソーシャルメディアをフォロー

最新の投稿

プロジェクトのご相談はありますか?