Qilux Lighting

Why Do LED Lights Flicker? 7 Causes and Fixes

LED Işıklar Neden Titreşir? 7 Neden ve Çözüm

Why do LED lights flicker? On a real site there are seven answers, and six of them are in the installation rather than the lamp. The symptom usually narrows the cause within a minute: a flicker that only appears below 20% is a dimmer-driver mismatch, a flicker that starts when the kettle goes on is a supply or neutral problem, and a flicker that only exists on video is a PWM frequency problem. This page names each cause, gives the number that decides it, and ends with a five-step order that finds the culprit without swapping every fixture in the room.

1. Flicker vs shimmer vs strobe: naming the problem

Four different faults get called “flicker”, each with a different fix. Naming yours saves a week.

Flicker is continuous modulation of light output at a steady frequency — usually 100 or 120 Hz mains ripple, sometimes higher. Shimmer is low-depth modulation you notice at low dim levels, typically under 10% output, where the driver is working near its stability limit. Strobe is deep, low-frequency modulation, often below 20 Hz, which reads as a pulse rather than a wobble. Stroboscopic effect is not flicker at all: the light is steady, but a moving object appears to jump, which is what happens under a high-frequency source at a short camera shutter.

There are also two faults that are not modulation. A dropout is the driver restarting, so the light blinks once every few seconds. A flash on switch-on is inrush charging the driver’s capacitor through the dimmer. Both look like flicker to a guest and neither is fixed by changing the driver’s PWM setting.

Three questions eliminate half the list before you touch anything: does it flicker at 100% or only when dimmed, does it happen with the switch off, and does it appear only on camera. Flicker at 1% with no camera points at the driver; a glow with the switch off points at leakage; a band on video points at frequency.

2. Cause 1: dimmer and driver mismatch

This is the most common cause and the easiest to prove. A phase-cut dimmer chops the mains waveform; the driver has to interpret what is left. Leading-edge (TRIAC) dimming was designed for a resistive filament, and it switches on mid-cycle into a capacitive load. The driver’s input capacitor charges in a short spike, the dimmer sees a current surge, and both ends oscillate. The result is a buzz you can hear and a flicker you can see, worst at the bottom of the travel.

Leading-edge and trailing-edge phase-cut waveform concepts for LED dimmer compatibility

Trailing-edge dimming switches off at the zero crossing and on at the start of the next half cycle, which suits a capacitive LED input far better. It is quieter and more stable, and it is what a retrofit should use. The catch is that the driver still has to be phase-cut capable: a trailing-edge dimmer on a driver with no phase-cut input will simply not dim, or will flicker at every level.

Leading edge (TRIAC)Trailing edge (MOSFET)
Switching pointMid-cycle, onZero crossing, off
Load it suitsResistive, inductiveCapacitive, LED drivers
Typical artefactsBuzz, inrush spike, dead bandMisfire at low load, heat
Minimum load10–20% of rating10–20%, often higher with LED
Depth reached in practice5–10%5–10%

The test is cheap: put one fixture on a known-compatible trailing-edge dimmer on a bench. If the flicker goes, the dimmer was the problem. If it stays, move to cause 2.

3. Cause 2: minimum load and phantom load

A dimmer needs current through it to work. Below its minimum load it cannot hold the switching element stable, so it misfires at the zero crossing and the lamp stutters. The rule of thumb is 10–20% of rated dimmer load, and some designs want 25%. Four 9 W downlights is 36 W; on a 400 W dimmer that is 9%, which is under the floor and will flicker at low dim regardless of brand.

Phantom load is the mirror image, and shows up with the switch off. A two-wire dimmer has no neutral, so it powers its own electronics by leaking a small current through the lamp — typically under 0.5 mA. One lamp ignores it. Twenty lamps in parallel turn that leakage into a visible glow or a slow blink, because each driver’s input capacitor charges until it fires. The complaint — “the lights flash in the middle of the night” — is real and it is not a wiring fault.

Fixes, in order of cost: raise the load on the circuit, fit a dimmer with a neutral, or specify drivers with lower leakage. Adding one incandescent lamp used to be the standard trick; it still works, but it costs 60 W of heat forever and fails an energy model.

4. Cause 3: wiring and shared neutral issues

Shared neutrals produce the strangest symptoms. Two lighting circuits on one neutral is common in older buildings, and if the circuits are on different phases the neutral carries the sum. Voltage between the two circuit neutrals then appears across the driver’s input, and the light flickers or fails when the other circuit loads up.

The tell is timing. Flicker that starts when a lift or kitchen circuit operates is a supply-path problem, not a driver one, and the same applies when it vanishes on a temporary feed.

Long switch drops cause a related fault. A 30 m run of 1.5 mm² cable couples enough induced voltage onto the switched line to keep twenty high-impedance drivers half-awake, and a smart dimmer with no neutral behaves the same way. Check for that neutral at survey, not after the plaster is finished.

One safety note matters for hotel work: a borrowed neutral trips an RCD when the circuits are energised separately, and it is a fire risk in a way a flickering lamp is not. If the flicker comes with a tripping RCD, stop.

5. Cause 4: driver quality and ripple

Every LED driver rectifies mains, and unless the output is well filtered, the LED sees a DC level with 100 Hz (or 120 Hz) ripple on top. Cheap drivers save money on output capacitance, and the ripple depth climbs: a good driver holds percent flicker under 5% and a flicker index below 0.1, a poor one sits at 20–40%. The light looks fine at full output and turns obvious at 10%, where ripple is a larger fraction of a smaller average.

Ripple also shortens life: the die is driven above and below its average current thousands of times a minute, and the thermal cycling accumulates at the wire bonds. That is one reason a cheap retrofit fails at year three while the datasheet suggests ten.

6. Cause 5: PWM frequency and camera capture

If the light is fine to the eye and bands on video, the cause is PWM. A driver that dims by switching the LED on and off at 200 Hz is invisible to most people and unusable on camera, because a shutter at 1/50 s or 1/100 s samples the waveform at a different point in each frame. The result is rolling bands or a strobe effect in the edit.

Photographers and video crews have practical thresholds. Below 1 kHz, banding is likely at normal shutter speeds. Above 3 kHz, most cameras at 1/1000 s and most high-speed rigs are clean. Between the two, results depend on the camera and the shutter, which is why “camera safe” claims need a test rather than a logo.

Two workarounds exist and both cost something: slow the shutter, which the director may refuse, or change the driver for one above 3 kHz or a CCR type with no PWM at all. On a ballroom or press room, put the frequency in the fixture schedule and ask for a test clip at 1/1000 s before the event.

7. Cause 6: supply voltage and dimmer type

Drivers have a minimum operating voltage, and at low dim the margin gets thin. A circuit that sits at 207 V — within the ±10% band around 230 V — may be fine at full output and drop out at 5%, because the driver’s internal rail is already near its limit and the dimming stage pulls it lower. Long runs make it worse: 40 m of 2.5 mm² cable at 10 A loses about 2.5% of the supply, and that is before the joint resistance in a few old back boxes.

The dimmer type matters as much as the voltage. A dimmer rated for MLV (magnetic low voltage) loads has a different output stage from one rated for ELV (electronic) loads, and putting an LED driver on an MLV-rated dimmer is a mismatch even if the wattage adds up. Check the dimmer’s stated load type against the driver’s input type, not the total load alone.

Check the dimmer’s rating table for the word “LED”: a figure stated for incandescent is not a rating for this load. Measure at the fixture under load and again at 10% dim; more than a 5% drop from the board points at the cable.

8. Cause 7: incompatible lamps on one circuit

Mixing brands on one dimmer is the last cause and the one most often created by maintenance. A hotel replaces twelve failed lamps with a different brand because the original is discontinued; the new drivers have different input characteristics, different inrush and a different minimum load. The dimmer now sees a composite load it was never tested against, and the whole circuit flickers even though each lamp is individually fine.

The same happens when a circuit mixes LED with a leftover halogen, or when a phase-cut circuit has a 0–10 V fixture added by mistake: one driver oscillating pulls the supply down enough to make its neighbours oscillate, so the fault looks like it is everywhere. The fix is discipline, not electronics. Keep one driver family per dimmed circuit, record the model in the O&M manual, and replace failures with the specified type.

9. A five-step diagnostic order

Bu sırayla ilerleyin; böylece arızaya hiç neden olmamış bir sürücüyü değiştirmezsiniz.

Five-step LED flicker troubleshooting flow covering symptoms, compatibility, load and professional checks

Adım 1 — sorunu yeniden oluşturun ve zamanlamasını belirleyin. Işık seviyesini, günün saatini ve aynı anda nelerin devreye girdiğini not edin. Başka bir cihazın çalışmasıyla bağlantılı titreme 3. nedendir; ışık seviyesine bağlı titreme ise 1, 2 veya 5. nedendir.

Adım 2 — devreyi yalıtın. Bir armatürü bir kısma anahtarına bağlayıp tezgâhta veya geçici bir beslemeyle deneyin. Sorun ortadan kalkarsa devre kaynaklıdır. Sorun armatürle birlikte devam ederse armatür kaynaklıdır.

Adım 3 — kısma anahtarını değiştirerek deneyin. Uyumlu olduğu bilinen bir arka kenar kısma anahtarı, servis ziyaretinden daha ucuza mal olur ve uyumsuzluk sorununu dakikalar içinde açıklığa kavuşturur.

Adım 4 — ölçüm yapın. Yük akımını 0 ve seviyelerinde pens ampermetreyle ölçün, armatürdeki gerilimi ölçün ve 2 kHz’in üzerinde örnekleme yapan bir ölçüm cihazıyla titreme yüzdesini kaydedin. Ölçüm sonuçları, tedarikçiyle tartışmayı sona erdirir.

Adım 5 — kanıtlarla konuyu üst kademeye taşıyın. Sürücü ve kısma anahtarı modellerini, ölçülen yükü, titreme değerlerini ve ağır çekim bir video kaydını gönderin. Bu verileri gören tedarikçi sürücüyü değiştirir; yalnızca “titriyor” ifadesini gören tedarikçi ise kabloları kontrol etmenizi ister.

BelirtiEn olası nedenİlk test
Yalnızca ışık ’nin altına kısıldığında titremeKısma anahtarı ile sürücü uyumsuzluğu veya asgari yük sorunuArka kenar kısma anahtarıyla tezgâh testi
Anahtar kapalıyken ışığın sönük yanması veya yanıp sönmesiKaçak akım / hayalet yükKaçak akımı ölçün, devredeki sürücüleri sayın
Başka bir devre çalışırken ışık titremesiOrtak veya ödünç alınmış nötr iletkenDevreyi izole edin ve yeniden besleyin
Videoda çizgiler oluşuyor, gözle fark edilmiyorPWM frekansı 3 kHz'nin altındaÖnce ağır çekim video, ardından sürücü veri sayfası
Uzun bir hat üzerinde düşük kısma seviyesinde titremeArmatürdeki gerilim düşümüYük altında gerçek RMS ölçümü
Tek devre, birden fazla markaMixed drivers on one dimmerStandardise the driver model

Frequently asked questions

Is LED flicker dangerous?

At the levels that matter, yes for some people. Modulation between 3 and 70 Hz is associated with photosensitive seizures, with 15–20 Hz the worst band. Steady 100 Hz ripple at high depth is linked to headache and eye strain over a working day. Low-depth flicker is a comfort problem, not a hazard, but it is worth fixing.

Why do my LED lights only flicker when dimmed?

Because the fault is in the dimming path, not the lamp. At full output the driver runs in a stable condition; at low output it is near its control limit, where a mismatched dimmer, a minimum-load shortfall or a voltage drop is enough to push it out of regulation. That is why the first test is a bench run at 10% and 1%.

Can a failing driver cause flicker?

Yes. A driver with a dried output capacitor loses filtering, so ripple climbs before it fails completely. The early symptom is a light that flickers at low dim or pulses once a second. If a fixture that used to be stable starts flickering and nothing else changed, suspect the driver before the wiring.

Do all dimmable LED lights flicker?

All of them modulate to some degree, because no driver is perfectly smooth. What differs is depth and frequency. A good driver holds percent flicker under 5% at every level; a poor one sits at 20–40% at 10%. “Flicker free” on a box is a marketing claim until a measurement supports it.

Next step

If a circuit is misbehaving, the fastest route is a compatibility check against the drivers you actually have. The driver and controls team will review your dimmer list, load counts and downlight schedule and flag the combinations that will flicker before they are installed. For the guestroom control logic that sits on top of this, the hotel dimming and switching guide covers scenes and key cards.

Christina

Hello, I’m Christina, founder of Qilux Lighting.Qilux Lighting is a China-based decorative and commercial lighting partner, working with distributors, lighting designers, system integrators, and project contractors worldwide.We support commercial and hospitality projects by translating design concepts into reliable, manufacturable lighting solutions, bridging design, production, and delivery.