Qilux Lighting

Why Do LED Lights Flicker? 7 Causes and Fixes

Warum flackern LED-Leuchten? 7 Ursachen und Lösungen

Why do LED lights flicker? On a real site there are seven answers, and six of them are in the installation rather than the lamp. The symptom usually narrows the cause within a minute: a flicker that only appears below 20% is a dimmer-driver mismatch, a flicker that starts when the kettle goes on is a supply or neutral problem, and a flicker that only exists on video is a PWM frequency problem. This page names each cause, gives the number that decides it, and ends with a five-step order that finds the culprit without swapping every fixture in the room.

1. Flicker vs shimmer vs strobe: naming the problem

Four different faults get called “flicker”, each with a different fix. Naming yours saves a week.

Flicker is continuous modulation of light output at a steady frequency — usually 100 or 120 Hz mains ripple, sometimes higher. Shimmer is low-depth modulation you notice at low dim levels, typically under 10% output, where the driver is working near its stability limit. Strobe is deep, low-frequency modulation, often below 20 Hz, which reads as a pulse rather than a wobble. Stroboscopic effect is not flicker at all: the light is steady, but a moving object appears to jump, which is what happens under a high-frequency source at a short camera shutter.

There are also two faults that are not modulation. A dropout is the driver restarting, so the light blinks once every few seconds. A flash on switch-on is inrush charging the driver’s capacitor through the dimmer. Both look like flicker to a guest and neither is fixed by changing the driver’s PWM setting.

Three questions eliminate half the list before you touch anything: does it flicker at 100% or only when dimmed, does it happen with the switch off, and does it appear only on camera. Flicker at 1% with no camera points at the driver; a glow with the switch off points at leakage; a band on video points at frequency.

2. Cause 1: dimmer and driver mismatch

This is the most common cause and the easiest to prove. A phase-cut dimmer chops the mains waveform; the driver has to interpret what is left. Leading-edge (TRIAC) dimming was designed for a resistive filament, and it switches on mid-cycle into a capacitive load. The driver’s input capacitor charges in a short spike, the dimmer sees a current surge, and both ends oscillate. The result is a buzz you can hear and a flicker you can see, worst at the bottom of the travel.

Leading-edge and trailing-edge phase-cut waveform concepts for LED dimmer compatibility

Trailing-edge dimming switches off at the zero crossing and on at the start of the next half cycle, which suits a capacitive LED input far better. It is quieter and more stable, and it is what a retrofit should use. The catch is that the driver still has to be phase-cut capable: a trailing-edge dimmer on a driver with no phase-cut input will simply not dim, or will flicker at every level.

Leading edge (TRIAC)Trailing edge (MOSFET)
Switching pointMid-cycle, onZero crossing, off
Load it suitsResistive, inductiveCapacitive, LED drivers
Typical artefactsBuzz, inrush spike, dead bandMisfire at low load, heat
Minimum load10–20% of rating10–20%, often higher with LED
Depth reached in practice5–10%5–10%

The test is cheap: put one fixture on a known-compatible trailing-edge dimmer on a bench. If the flicker goes, the dimmer was the problem. If it stays, move to cause 2.

3. Cause 2: minimum load and phantom load

A dimmer needs current through it to work. Below its minimum load it cannot hold the switching element stable, so it misfires at the zero crossing and the lamp stutters. The rule of thumb is 10–20% of rated dimmer load, and some designs want 25%. Four 9 W downlights is 36 W; on a 400 W dimmer that is 9%, which is under the floor and will flicker at low dim regardless of brand.

Phantom load is the mirror image, and shows up with the switch off. A two-wire dimmer has no neutral, so it powers its own electronics by leaking a small current through the lamp — typically under 0.5 mA. One lamp ignores it. Twenty lamps in parallel turn that leakage into a visible glow or a slow blink, because each driver’s input capacitor charges until it fires. The complaint — “the lights flash in the middle of the night” — is real and it is not a wiring fault.

Fixes, in order of cost: raise the load on the circuit, fit a dimmer with a neutral, or specify drivers with lower leakage. Adding one incandescent lamp used to be the standard trick; it still works, but it costs 60 W of heat forever and fails an energy model.

4. Cause 3: wiring and shared neutral issues

Shared neutrals produce the strangest symptoms. Two lighting circuits on one neutral is common in older buildings, and if the circuits are on different phases the neutral carries the sum. Voltage between the two circuit neutrals then appears across the driver’s input, and the light flickers or fails when the other circuit loads up.

The tell is timing. Flicker that starts when a lift or kitchen circuit operates is a supply-path problem, not a driver one, and the same applies when it vanishes on a temporary feed.

Long switch drops cause a related fault. A 30 m run of 1.5 mm² cable couples enough induced voltage onto the switched line to keep twenty high-impedance drivers half-awake, and a smart dimmer with no neutral behaves the same way. Check for that neutral at survey, not after the plaster is finished.

One safety note matters for hotel work: a borrowed neutral trips an RCD when the circuits are energised separately, and it is a fire risk in a way a flickering lamp is not. If the flicker comes with a tripping RCD, stop.

5. Cause 4: driver quality and ripple

Jeder LED-Treiber gleichrichtet die Netzspannung. Ist der Ausgang nicht ausreichend gefiltert, liegt an der LED eine Gleichspannung mit einer überlagerten Restwelligkeit von 100 Hz (oder 120 Hz) an. Bei günstigen Treibern wird an der Ausgangskapazität gespart, wodurch die Restwelligkeit zunimmt: Ein guter Treiber hält das prozentuale Flimmern unter 5 % und den Flimmerindex unter 0,1; bei einem schlechten liegt es bei 20–40 %. Bei voller Leistung wirkt das Licht unauffällig. Bei 10 % wird das Flimmern deutlich, weil die Restwelligkeit im Verhältnis zum niedrigeren Mittelwert stärker ins Gewicht fällt.

Die Restwelligkeit verkürzt auch die Lebensdauer: Der Chip wird tausende Male pro Minute mit einem Strom ober- und unterhalb des Mittelwerts betrieben, und die thermischen Zyklen belasten die Drahtbondverbindungen. Das ist ein Grund dafür, dass ein günstiger Retrofit-Leuchtkörper bereits im dritten Jahr ausfällt, obwohl das Datenblatt eine Lebensdauer von zehn Jahren angibt.

6. Ursache 5: PWM-Frequenz und Kameraaufnahme

Wenn das Licht mit dem Auge unauffällig wirkt, auf Videos aber Streifen zeigt, liegt die Ursache bei der PWM. Ein Treiber, der die LED durch Ein- und Ausschalten mit 200 Hz dimmt, ist für die meisten Menschen nicht wahrnehmbar, aber für Kameraaufnahmen ungeeignet: Bei einer Belichtungszeit von 1/50 s oder 1/100 s erfasst der Verschluss die Wellenform in jedem Bild an einem anderen Punkt. Das Ergebnis sind wandernde Streifen oder ein Stroboskopeffekt im Schnitt.

Für Fotografen und Filmteams gelten praktische Richtwerte. Unter 1 kHz, treten bei üblichen Belichtungszeiten wahrscheinlich Streifen auf. Oberhalb von 3 kHz, liefern die meisten Kameras bei 1/1000 s und die meisten Hochgeschwindigkeitskameras saubere Bilder. Dazwischen hängt das Ergebnis von Kamera und Belichtungszeit ab. Deshalb sollte man Aussagen wie “kameratauglich” testen, statt sich auf ein Logo zu verlassen.

Es gibt zwei Abhilfen, und beide haben Nachteile: Entweder wird die Belichtungszeit verlängert, was der Regisseur möglicherweise ablehnt, oder der Treiber wird gegen ein Modell mit mehr als 3 kHz beziehungsweise einen CCR-Treiber ohne PWM ausgetauscht. Bei einem Ballsaal oder einem Presseraum sollte die Frequenz im Leuchtenverzeichnis angegeben und vor der Veranstaltung ein Testclip mit 1/1000 s angefordert werden.

7. Ursache 6: Versorgungsspannung und Dimmerart

Treiber haben eine Mindestbetriebsspannung, und bei niedriger Dimmstufe wird die Reserve knapp. Ein Stromkreis mit 207 V – innerhalb des Toleranzbereichs von ±10 % um 230 V – kann bei voller Leistung einwandfrei funktionieren und bei 5 % ausfallen, weil die interne Versorgungsspannung des Treibers bereits nahe an ihrer Grenze liegt und die Dimmstufe sie weiter absenkt. Lange Leitungswege verschärfen das Problem: 40 m Kabel mit 2,5 mm² Querschnitt verursachen bei 10 A einen Spannungsabfall von etwa 2,5 %, zusätzlich zu den Übergangswiderständen in einigen alten Unterputzdosen.

Die Dimmerart ist ebenso wichtig wie die Spannung. Ein Dimmer für MLV-Lasten (magnetische Niedervoltlasten) hat eine andere Ausgangsstufe als ein Dimmer für ELV-Lasten (elektronische Niedervoltlasten). Einen LED-Treiber an einen für MLV ausgelegten Dimmer anzuschließen, ist daher eine Fehlanpassung – auch wenn die Gesamtleistung passt. Vergleichen Sie die angegebene Lastart des Dimmers mit der Eingangsart des Treibers, nicht nur die Gesamtlast.

Prüfen Sie in der Belastungstabelle des Dimmers, ob “LED” aufgeführt ist: Ein für Glühlampen angegebener Wert gilt nicht für diese Last. Messen Sie die Spannung an der Leuchte unter Last und erneut bei 10 % Dimmstufe. Ein Abfall von mehr als 5 % gegenüber der Verteilung weist auf ein Problem mit der Leitung hin.

8. Ursache 7: inkompatible Lampen in einem Stromkreis

Die Mischung verschiedener Marken an einem Dimmer ist die letzte mögliche Ursache und entsteht am häufigsten bei Wartungsarbeiten. Ein Hotel ersetzt zwölf defekte Lampen durch eine andere Marke, weil das ursprüngliche Modell nicht mehr erhältlich ist. Die neuen Treiber haben andere Eingangseigenschaften, einen anderen Einschaltstrom und eine andere Mindestlast. Der Dimmer sieht nun eine gemischte Last, für die er nie getestet wurde, und der gesamte Stromkreis flimmert, obwohl jede Lampe einzeln einwandfrei funktioniert.

Dasselbe passiert, wenn in einem Stromkreis LED-Lampen mit einer verbliebenen Halogenlampe kombiniert werden oder versehentlich eine 0–10-V-Leuchte zu einem Phasenanschnitt- oder Phasenabschnitt-Stromkreis hinzugefügt wird: Ein schwingender Treiber senkt die Versorgungsspannung so weit ab, dass auch die anderen zu schwingen beginnen. Dadurch scheint der Fehler überall aufzutreten. Die Lösung ist eine konsequente Vorgehensweise, keine zusätzliche Elektronik. Verwenden Sie in jedem gedimmten Stromkreis nur eine Treiberfamilie, dokumentieren Sie das Modell im O&M-Handbuch und ersetzen Sie defekte Geräte durch den vorgeschriebenen Typ.

9. Diagnostik in fünf Schritten

Gehen Sie in dieser Reihenfolge vor, damit Sie keinen Treiber ersetzen, der gar nicht die Ursache war.

Five-step LED flicker troubleshooting flow covering symptoms, compatibility, load and professional checks

Schritt 1 — Fehler reproduzieren und zeitlich einordnen. Beachten Sie die Dimmstufe, die Tageszeit und welche weiteren Geräte eingeschaltet wurden. Tritt das Flackern zusammen mit einem anderen Gerät auf, ist Ursache 3 wahrscheinlich; hängt es von der Dimmstufe ab, kommt Ursache 1, 2 oder 5 infrage.

Schritt 2 — Stromkreis isolieren. Schließen Sie eine Leuchte an einen einzelnen Dimmer an, auf einer Werkbank oder an einer provisorischen Stromversorgung. Verschwindet der Fehler, liegt das Problem am Stromkreis. Tritt er weiterhin bei der Leuchte auf, liegt es an der Leuchte.

Schritt 3 — Dimmer austauschen. Ein nachweislich kompatibler Phasenabschnittdimmer kostet weniger als ein Kundendienstbesuch und klärt die Frage nach einer Inkompatibilität in wenigen Minuten.

Schritt 4 — messen. Messen Sie den Laststrom bei 100 % und 10 %, die Spannung an der Leuchte und den Flackeranteil mit einem Messgerät, das mit mehr als 2 kHz abtastet. Die Messwerte beenden die Diskussion mit dem Lieferanten.

Schritt 5 — mit Belegen eskalieren. Senden Sie die Modellbezeichnungen von Treiber und Dimmer, die gemessene Last, die Flackerwerte und ein Zeitlupenvideo. Sieht ein Lieferant diese Daten, tauscht er den Treiber aus; hört er nur “es flackert”, fordert er Sie auf, die Verdrahtung zu prüfen.

SymptomWahrscheinlichste UrsacheErster Test
Flackern nur bei einer Dimmung unter 20 %Inkompatibilität zwischen Dimmer und Treiber oder MindestlastPrüfung auf einer Werkbank mit einem Phasenabschnittdimmer
Leuchten oder Blinken bei ausgeschaltetem SchalterLeckstrom / ScheinlastLeckstrom messen und Treiber im Stromkreis zählen
Flackern beim Betrieb eines anderen StromkreisesGemeinsam genutzter oder mitbenutzter NeutralleiterStromkreis freischalten und erneut einspeisen
Streifen im Video, mit bloßem Auge unauffälligPWM-Frequenz unter 3 kHzZeitlupenaufnahme, anschließend Treiberdatenblatt
Flimmern bei geringer Dimmung über eine lange LeitungSpannungsabfall an der LeuchteTrue-RMS-Messung unter Last
Ein Stromkreis, mehrere MarkenVerschiedene Treiber an einem DimmerTreibermodell vereinheitlichen

Häufig gestellte Fragen

Is LED flicker dangerous?

At the levels that matter, yes for some people. Modulation between 3 and 70 Hz is associated with photosensitive seizures, with 15–20 Hz the worst band. Steady 100 Hz ripple at high depth is linked to headache and eye strain over a working day. Low-depth flicker is a comfort problem, not a hazard, but it is worth fixing.

Why do my LED lights only flicker when dimmed?

Because the fault is in the dimming path, not the lamp. At full output the driver runs in a stable condition; at low output it is near its control limit, where a mismatched dimmer, a minimum-load shortfall or a voltage drop is enough to push it out of regulation. That is why the first test is a bench run at 10% and 1%.

Can a failing driver cause flicker?

Yes. A driver with a dried output capacitor loses filtering, so ripple climbs before it fails completely. The early symptom is a light that flickers at low dim or pulses once a second. If a fixture that used to be stable starts flickering and nothing else changed, suspect the driver before the wiring.

Do all dimmable LED lights flicker?

All of them modulate to some degree, because no driver is perfectly smooth. What differs is depth and frequency. A good driver holds percent flicker under 5% at every level; a poor one sits at 20–40% at 10%. “Flicker free” on a box is a marketing claim until a measurement supports it.

Nächster Schritt

If a circuit is misbehaving, the fastest route is a compatibility check against the drivers you actually have. The driver and controls team will review your dimmer list, load counts and downlight schedule and flag the combinations that will flicker before they are installed. For the guestroom control logic that sits on top of this, the hotel dimming and switching guide covers scenes and key cards.

Christina

Hello, I’m Christina, founder of Qilux Lighting.Qilux Lighting is a China-based decorative and commercial lighting partner, working with distributors, lighting designers, system integrators, and project contractors worldwide.We support commercial and hospitality projects by translating design concepts into reliable, manufacturable lighting solutions, bridging design, production, and delivery.

Neuester Beitrag

Haben Sie ein Projekt im Sinn?